AXXESS AXBUC-VW92 Backup Camera Retention Interface Instruction Manual
INTERFACE FEATURES
- AXBUC-VW92 interface
- BLK-AXBUC-VW92 harness
INTERFACE FEATURES
- Retains the OEM camera to an aftermarket radio
- Plug-and-play, no cutting of wires required
- For vehicles equipped with RNS510 (MFD3), RNS315, Columbus (Skoda), or RCD510 (with 26-pin connector)
NOTE: If your vehicle has a motorized OE camera door or active guidelines, you will need an interface that can enable the camera door to open, the AXBUC-VW2 will not retain these function. The AXBUC-VW2 will only retain the camera.
APPLICATIONS
Volkswagen
Amarok ……………………………………..2010-2014
EOS ………………………………………….. 2009-2014
Golf …………………………………………..2008-2014
Jetta …………………………………………2009-2014
Passat ………………………………………..2010-2015
Polo ………………………………………….2008-2014
Scirocco …………………………………….2008-2015
Tiguan ………………………………………. 2009-2015
Touran ……………………………………….2010-2015
Transporter ……………………………….2009-2014
Skoda
Octavia ……………………………………..2009-2012
Superb ……………………………………..2008-2015
TOOLS REQUIRED
- Crimping tool and connectors, or solder gun, solder, and heat shrink
- Tape
- Wire cutter
- Zip ties
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications
ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product.
NOTE: Refer also to the instructions included with the aftermarket radio.
CONNECTIONS: BLK-AXBUC-VW92
INSTALLING THE INTERFACE & DIP SWITCH SETTINGS
- Connect the AXBUC-VW92 to the wiring harness in the vehicle located at the radio location (26-pin connector).
Installation Steps
- Connect Ground wire from the VW92 to the aftermarket radio’s ground wire.
- Connect the Yellow wire from the VW92 to the Yellow wire of your aftermarket radio.
- Purple is a Reverse input, connect the reverse trigger from your vehicle or interface to this wire. Do not connect this wire to the vehicle’s BCM for the reverse signal. VW uses PWM circuitry, if connected to the BCM, the backup camera will flicker while the vehicle is running. You must find a dedicated reverse signal or use an interface that provides a reverse output.
- Plug in the CAM OUT Video cable into the rear view camera input of your aftermarket radio.
- Plug in the White connector into the interface box. 6. Plug in the vehicle connector and test.
Dip Switch Settings
If after the AXBUC-VW2 is installed your screen quickly flashes the backup camera, or is displaying a blank screen when you put the vehicle into reverse, you will need to adjust the dip switches on the side of the interface.
If screen is blank or flashing while in reverse, try this sequence.
Step 1 – Set Dip Switch 3 to OFF. – If not working go to step 2.
Step 2 – Move all Dip Switches to OFF – If not working go to step 3.
Step 3 – Flip Dip Switch 3 ON, leaving 1,2,4 OFF.
Having difficulties? We’re here to help. Contact our Tech Support line at:
386-257-1187
Or via email at: techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 5:00 PM
Sunday: 10:00 AM – 4:00 PM
Metra recommends MECP certified technicians
AxxessInterfaces.com © COPYRIGHT 2025 METRA ELECTRONICS CORPORATION REV. 5/27/25 INSTAXBUC-VW92
Documents / Resources
 |
AXXESS AXBUC-VW92 Backup Camera Retention Interface [pdf] Instruction Manual AXBUC-VW92 Backup Camera Retention Interface, AXBUC-VW92, Backup Camera Retention Interface, Camera Retention Interface, Retention Interface, Interface |