AUTOMATE Push 15 Channel Remote Control User Guide
SAFETY
⚠ WARNING: Important safety instructions to be read before installation and use.
Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty. It is important for the safety of persons to follow the enclosed instructions.
Save these instructions for future reference.
- Do not expose to water, moisture, humid and damp environments or extreme temperatures.
- Persons {including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, should not be allowed to use this product.
- Use or modification outside the scope of this instruction manual will void warranty.
- Installation and programming to be performed by a suitably qualified installer.
- Follow installation instructions.
- For use with motorized shading devices.
- Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
- Keep clear when in operation.
- Replace battery with correctly specified type.
⚠ WARNING: Do not ingest battery, Chemical Burn Hazard.
This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Operation Temperature Range, -10°C to +50°C Ratings, JVDC, 15mA
FCC & ISED STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver( s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 1 S of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ASSEMBLY
Please refer to separate Release Almeda System Assembly Manual for full assembly instructions relevant to the hardware system being used.
BATTERY MANAGEMENT
Prevent discharging the battery completely far extended periods, recharge as soon as the battery is discharged
CHARGING NOTES
Charge your motor far 6-8 hours, depending on the motor model, as per motor instructions
⚠ During operation, if battery is low, the motor will beep 10 times to prompt the user it needs charging.
P1 LOCATIONS
WALL MOUNTING
Use supplied fasteners and anchors to attach the base to wall.
HOW TO CHARGE LI-ION ZERO WIRE-FREE MOTOR
REPLACE BATTERY
ON REMOTE
CHECK DIRECTION
STEP 3.
Press up or down to check the motor direction. If correct skip to step 5.
CHANGE DIRECTION
SET TOP LIMIT
SET BOTTOM LIMIT
FACTORY RESET
REMOTE STATE
GROUP PROGRAMMING MODE
It is possible to add Individual Channels [1- 5] to create Custom Groups [A-E]
GROUP CHANNEL VIEW MODE
LEVELING CONTROL FUNCTION
CHANNEL OR GROU SELECTION
HIDE GROUPS
HIDE CHANNELS
Note: Ensu1e all shade programming for all motors is completed before locking the remote.
User mode prevent accidental or unintended changing of limits.
SET A FAVORITE POSITION
ADD OR DELETE CONTROLLER OR t ANNEL
Documents / Resources
 |
AUTOMATE Push 15 Channel Remote Control [pdf] User Guide Push 15 Channel Remote Control, Push 15, Channel Remote Control, Remote Control |
 |
AUTOMATE Push 15 Channel Remote Control [pdf] User Guide 003B9ACA41, 2AGGZ003B9ACA41, Push 15, Push 15 Channel Remote Control, Channel Remote Control, Remote Control |
