Categories: Atlantic

ATLANTIC 38436252 Henley Multimedia Cabinet User Manual

ATLANTIC 38436252 Henley Multimedia Cabinet

Contents hide

5 Documents / Resources

5.1 References

6 Related Posts

Assembly Tips:

Become familiar with the instructions and all parts.
Make sure that all parts are in the box and in good condition.
Assemble the product on the open flat carton or a rug to protect the product and your floor.
Some heavy products need a second person to assist in the assembly.
Use of power tools is not recommended.

Care Instructions

Use electrostatic dust cloths to clean furniture. Do not set hot or cold containers directly on the furniture surface.

Caution:
Never let children climb on furniture or play with furniture.
Do not place a weight heavier than the recommended load rating on the furniture surface.
Use care when moving furniture. Furniture can tip over if moved improperly.
Improper handling can result in cuts and lacerations.
Do not install on sloping surface.

Parts List

Use Phllllps screwdriver fo, assembty. Powe.r tools may damage engineered wood panels.
Tools Needed (not included)
Herramanientas requeridas (no incluidas)

Drill and Drill Bit	Phillips Screwdriver	Pencil
Drill and Drill Bit	Stud Finder	Hammer

1 Using a Phillips screwdriver, screw six metal cam screws (AA) into center holes of panels (A) and (B).

2 Insert six wood dowels (DD) into panel (A). Then attach panels (D, F, and E) to panel (A). Insert cam locking nuts (BB) into (D, F, and E). Using a Phillips screwdriver, turn the nuts Clockwise until they lock.

3 To connect panel (B) to (D, F, and E), insert six screws (CC) into panel (B). Using a Phillips screwdriver, tighten screws. Do not over-tighten screws.

4 Insert six wood dowels (DD) into panel (B). Then attach panels (D, F, and E to panel (B). Insert cam locking nuts (BB) into (D, F, and E). Using a Phillips screwdriver, turn the nuts Clockwise until they lock.

5 To connect panel (C) to (D, F, and E), insert six screws (CC) into panel (C). Using a Phillips screwdriver tighten screws. Do not over-tighten screws.

6 With the back of the cabinet facing up, place the back panels (H and J) onto the frame. Insert 39 screws (EE) into panels (H and J), using a Phillips screwdriver to tighten.

7 Place the cabinet in an upright position. Insert 48 metal pins (FF) into the cabinet at the desired shelf heights. Use four pins per shelf. Assembly completed.

8a WOOD STUD MOUNTING
Use Phillips screwdriver to attach mounting bracket GG(B) with wood screw GG(C) into the predrilled hole on the side of the cabinet. Repeat for other side of cabinet. Using a stud finder, locate a wood stud. Position the cabinet so one of the brackets mounts into a stud, marking the hole position with a pencil. Drill a hole 1.5” deep with 1/8” drill bit. Use Phillips screwdriver to attach bracket GG(B) with screw GG(D) into drilled hole. Repeat for other bracket GG(B).

8b MASONRY MOUNTING
Use Phillips screwdriver to attach mounting bracket GG(B) with wood screw GG(C) into the predrilled hole on the top of the cabinet. Repeat for other side of cabinet. Marking the hole position with a pencil. Drill a hole 1.5” deep with a 3/16” drill bit. Pound wall anchor GG(A) into the masonry with a hammer. Use Phillips screwdriver to attach bracket GG(B) with screw GG(D) into the drilled hole. Repeat for other bracket GG(B).

Product Warranty

This Limited Warranty covers any defects in material or workmanship for purchases made in the U.S.A. and Canada, and excludes claims from conditions, malfunctions or damage not resulting from defects in material or workmanship. The warranty duration is one year.

©2020 Atlantic Inc.
Santa Fe Springs, CA. U.S.A
All rights reserved / Derechos Reservados
Made in China / Hecho en China
www.atlantic-inc.co