ASUS LCD Monitor VE228TL User Guide

ASUS USB 3.0 HZ-3D Docking Station - logo

VE228TL Series
LCD Monitor

User Guide

ASUS LCD Monitor VE228TL

First Edition
September 2013

Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved.

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or alered, unless such repair, modification of alteration is authorized in writing byASUS; or (2) the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation nd to the owners’ benefit, without intent to infringe.


ii

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference, and
  • This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Warning 1A blue

The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

This class B digital apparatus complies with Canadian ICES-003.

This Class B digital apparatus meets all requirements of the Canadian Interference – Causing Equipment Regulations.

EAL-Logo

 

 


iv

Safety information
  • Before setting up the monitor, carefully read all the documentation that came with the package.
  • To prevent fire or shock hazard, never expose the monitor to rain or moisture.
  • Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury.
  • If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
  • Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
  • Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided.
  • The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.
  • Use the appropriate power plug which complies with your local power standard.
  • Do not overload power strips and extention cords. Overloading can result in fire or electric shock.
  • Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface.
  • Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges.
  • Never push objects or spill liquid of any kind into the slots on the monitor cabinet.
  • To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC.
  • If you encounter technical problems with the monitor, contact a qualified service technician or your retailer.
  • Adjustment of the volume control as well as the equalizer to other settings than the center position may increase the ear-/headphones output voltage and therefore the sound pressure level.

Trash

This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercury-containing button cell battery) should not be placed in municipal waste. Please check local regulations for disposal of electronic products.

AEEE


v

Care & Cleaning
  • Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord.
  • Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner.
  • Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the monitor. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock.

The following symptoms are normal with the monitor:

  • The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears.
  • You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
  • When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours.
  • When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself!

Conventions used in this guide

Warning 1A blue

WARNING: Information to prevent injury to yourself when trying to complete a task.

Caution blue

CAUTION: Information to prevent damage to the components when trying to complete a task.

Important

IMPORTANT: Information that you MUST follow to complete a task.

 

Note A

NOTE: Tips and additional information to aid in completing a task.

 


vi

Where to find more information
Refer to the following sources for additional information and for product and software updates.

1. ASUS websites
The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to http://www.asus.com

2. Optional documentation
Your product package may include optional documentation that may have been added by your dealer. These documents are not part of the standard package.

Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials.

Please go to http://csr.asus.com/english/Takeback.htm for detail recycling information in different region.


vii


 


 


 



viii

1.1 Welcome!

Thank you for purchasing the ASUS® LCD monitor!

The latest widescreen LCD monitor from ASUS provides a broader, brighter and crystal-clear display, plus a host of features that enhance your viewing experience.

With these features, you can enjoy the convenience and delightful visual experience that the monitor brings to you!

1.2 Package contents

Check your package for the following items:
Bullet LCD monitor
Bullet Monitor base
Bullet Quick start guide
Bullet Warranty card
Bullet Power cord
Bullet VGA cable
Bullet DVI cable
Bullet Audio cable

Important

If any of the above items is damaged or missing, contact your retailer immediately.

1.3 Monitor introduction

1.3.1. Front view

Monitor's Front view

  1. S Button, A Button button:
    Selects a desired preset mode. S Button
    Exits the OSD menu or goes back to the previous menu when the OSD menu is active. S Button
    Automatically adjusts the image to its optimized position, clock, and phase by pressing this button for 2-4 seconds (for VGA mode only). A Button
  2. Volume hotkey & Decreases values
    Decreases values or moves your selection left/down.
    Volume hotkey
  3. MENU button:
    Turns on the OSD menu. Enacts the selected OSD menu item.
  4. Brightness hotkey & Increases values
    Increases values or moves your selection right/up.
    Brightness hotkey
  5. Power Button Power button/power indicator
    Turns the monitor on/off.
    The color definition of the power indicator is as the below table.
Status Description
Blue ON
Amber Standby mode
OFF OFF

1.3.2. Back view

Monitor's Back view

Rear connectors

  1. Audio-in port. This port connects PC (Personal Computer) audio source by the bundled audio cable.
  2. AC-IN port. This port connects the power cord.
  3. DVI port. This 24-pin port is for PC DVI-D digital signal connection.
  4. VGA port. This 15-pin port is for PC VGA connection.


 


 


 


 


2.1 Assembling the monitor arm/base

To assemble the monitor base:

  1. Have the front of the monitor face down on a table.
  2. Rotate the arm anti-clockwise 90 degrees. (Figure 1)
  3. Fix the base to the arm by fastening the bundled screw. (Figure 2) (Figure 3)
  4. Align the triangle mark on the base with the two screws to allow 160 degrees swivel from either left or right. (Figure 4)

Caution blue

We recommend that you cover the table surface with soft cloth to prevent damage to the monitor.

Assembling the monitor arm base - Figure 1      Arrow blueAssembling the monitor arm base - Figure 2 to 4

2.2 Adjusting the monitor
  • For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you.
  • Hold the stand to prevent the monitor from falling when you change its angle.
  • The recommended adjusting angle is +22° to -5° (for tilt)/+160° to -160° (for swiveling/ +130 mm (for height adjustment)/90° (for portrait view).

Adjusting the monitor 1    Adjusting the monitor 2    Adjusting the monitor 3    Adjusting the monitor 4

Note A

It is normal that the monitor slightly shakes while you adjust the viewing angle.

2.3 Detaching the arm/base (for VESA wall mount)

The detachable arm/base of this monitor is specially designed for VESA wall mount.

To detach the arm/base:

  1. Have the front of the monitor face down on a table.
  2. Loosen the four screws on the back of the monitor and remove the arm/base.

Detaching the arm base

Note A

We recommend that you cover the table surface with soft cloth to prevent damage to the monitor.

2.4 Connecting the cables

Connect the cables as the following instructions:

Connecting the cables

  • To connect the audio cable: connect one end of the audio cable to the monitor’s Audio-in port, the other end to the computer’s audio-out port.
  • To connect the power cord: connect one end of the power cord securely to the monitor’s AC input, the other end to a power outlet.
  • To connect the VGA/DVI cable:
    a. Plug one end of the VGA/DVI cable to the monitor’s VGA/DVI port.
    b. Connect the other end of the VGA/DVI cable to your computer’s VGA/ DVI port.
    c. Tighten the two screws to secure the VGA/DVI connector..

Note AWhen these cables are connected, you can choose the desired signal from the Input Select item in the OSD menu.

2.5 Turning on the monitor

Press the power button Power Button. See page 1-2 for the location of the power button. The power indicator Power Button lights up in blue to show that the monitor is ON.


 


 


 


 


 


 


 


3.1 OSD (On-Screen Display) menu

How to reconfigure

3.1.1 How to reconfigure

  1. Press the MENU button to activate the OSD menu.
  2. Press  Volume hotkey & Decreases values, Brightness hotkey & Increases values and to navigate through the functions. Highlight the desired function and press the MENU button to activate it. If the function selected has a sub-menu, press Volume hotkey & Decreases values, Brightness hotkey & Increases values again to navigate through the sub-menu functions. Highlight the desired sub-menu function and press the MENU button to activate it.
  3. Press Volume hotkey & Decreases values, and Brightness hotkey & Increases values to change the settings of the selected function.
  4. To exit and save the OSD menu, press the S Button button repeatedly until the OSD menu disappears. To adjust other functions, repeat steps 1-3.

3.1.2 OSD function introduction

Splendid

1. Splendid

This function contains six subfunctions you can select for your preference. Each mode has the Reset selection allowing you to maintain your setting or return to the preset mode.

  • Scenery Mode: best choice for scenery photo display with SPLENDIDTM Video Enhancement.
  • Standard Mode: best choice for document editing with SPLENDIDTM Video Enhancement.
  • Theater Mode: best choice for movies with SPLENDIDTM Video Enhancement.
  • Game Mode: best choice for games playing with SPLENDIDTM Video Enhancement.
  • Night View Mode: best choice for dark-scene games or movies with SPLENDIDTM Video Enhancement.
  • sRGB: best choice for viewing photos and graphics from PCs.

Note AIn the Standard Mode, the ASCR, Saturation and Sharpness functions are not user-configurable.

Color2. Color

You can adjust Brightness, Contrast, Saturation, Color Temp., Skin Tone, and Smart View from this menu.

  • Brightness: the adjusting range is from 0 to 100. Brightness hotkey & Increases values is a hotkey to activate this function.
  • Contrast: the adjusting range is from 0 to 100.
  • Saturation: the adjusting range is from 0 to 100.
  • Color Temp.: contains four modes including Cool, Normal, Warm, and User Mode.
  • Skin Tone: contains three color modes including Reddish, Natural, and Yellowish.
  • Smart View: provides better display quality under big viewing angle.

Note AIn the User mode, colors of R (Red), G (Green), and B (Blue) are userconfigurable; the adjusting range is from 0-100.

Image
3. Image

You can adjust Sharpness, Aspect Control, ASCR, Position (VGA only), and Focus (VGA only) from this menu.

  • Sharpness: the adjusting range is from 0 to 100.
  • Aspect Control: adjusts the aspect ratio to “Full”, or “4:3”.
  • ASCR: turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
  • Position: adjusts the horizontal position (H-Position) and the vertical position (V-Position) of the image. The adjusting range is from 0 to 100.
  • Focus: reduces Horizonal-line noise and Vertical-line noise of the image by adjusting (Phase) and (Clock) separately. The adjusting range is from 0 to 100.

Note A

Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows horizontal disturbances.

Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the image is not proportional.

4. Input Select

In this function, you can select your desired input source.

5. System Setup

Allows you to adjust the system.

  • Splendid Demo Mode: splits the screen into two for Splendid modes comparison.
  • Volume: the adjusting range is from 0 to 100.
  • ECO Mode: reduces power consumption.
  • OSD Setup:
    * Adjusts the horizontal position (H-Position)/the vertical position (V-Position) of the OSD from 0 to 100.
    * Adjusts the OSD timeout from 10 to 120 seconds.
    * Enables or disables the DDC/CI function.
    * Adjusts the OSD background from opaque to transparent.
  • Information: shows the monitor information.
  • Language: there are 10 languages for your selection, including English, German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese, Simplified Chinese, and Japanese.
  • All Reset: “Yes” allows you to restore the default settings.
3.2 Specifications summary
Panel Type TFT LCD
Panel size 21.5”W (16:9, 54.6 cm) wide screen
Max. Resolution 1920 x 1080
Pixel pitch 0.248 mm
Brightness (Typ.) 250 cd/m2
Contrast Ratio (Typ.) 1000:1
Contrast Ratio (Max.) 80,000,000:1 (with ASCR on)
Viewing angle(H/V) CR>10 170˚/160˚
Display colors 16.7 M
Response time 5 ms
SPLENDID™ Video Enhancement Yes
SPLENDID™ selection 6 video preset modes (by hotkey)
Auto adjustment Yes (by hotkey)
Color temperature selection 4 color temperatures
Skin-Tone selection 3 skin-tones
Digital input DVI-D with HDCP
Analog input D-Sub
Audio-in port 3.5 mm Mini-jack
Colors Black
Speaker (Built-in) 1 W x 2 Stereo, RMS
Power LED Blue (On)/Amber (Standby)
Tilt +22˚~ -5˚
Swivel +160˚~-160˚
Height Adjustment 130 mm
VESA wall mount 100 x 100 mm
Kensington lock Yes
Voltage rating AC: 100~240V
Power consumption Power On: < 33 W, Standby: < 0.5 W, Power Off: < 0.5 W
Temperature (Operating) 0˚C~40˚C
Temperature (Non-operating) -20˚C~+60˚C
Dimensions (W x H x D) 512.84 mm x 484.36 mm x 225.0 mm (machine)

672 mm x 372 mm x 200 mm (package)

Weight (Esti.) 5.2 kg (Net); 6.2 kg (Gross)
Multi-languages 10 languages (English, German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese, Simplified Chinese, Japanese)
Accessories VGA cable, DVI cable, audio cable, power cord, Quick start guide, warranty card
Regulation approvals ISO 9241-307, UL/cUL, CB, CE, ErP, FCC, Gost-R, C-Tick, J-MOSS, RoHS, WEEE, C-TICK, UKrSEPRO, Windows 7 WHQL

*Specifications are subject to change without notice.

3.3             Troubleshooting (FAQ)

Problem

Possible Solution

Power LED is not ON • Press the Power Button button to check if the monitor is in the ON mode.

• Check if the power cord is properly connected to the monitor and the power outlet.

The power LED lights amber and there is no screen image • Check if the monitor and the computer are in the ON mode.

• Make sure the signal cable is properly connected the monitor and the computer.

• Inspect the signal cable and make sure none of the pins are bent.

• Connect the computer with another available monitor to check if the computer is properly working.

Screen image is too light or dark • Adjust the Contrast and Brightness settings via OSD.
Screen image is not centered or sized properly • Press the A Button button for 2-4 seconds to automatically adjust the image (for VGA mode only).

• Adjust the H-Position or V-Position settings via OSD.

Screen image bounces or a wave pattern is present in the image • Make sure the signal cable is properly connected to the monitor and the computer.

• Move electrical devices that may cause electrical interference.

Screen image has color defects (white does not look white) • Inspect the signal cable and make sure that none of the pins are bent.

• Perform All Reset via OSD.

• Adjust the R/G/B color settings or select the Color Temperature via OSD.

Screen image is blurry or fuzzy • Press the A Button button for 2-4 seconds to automatically adjust the image (for VGA mode only).

• Adjust the Phase and Clock settings via OSD.

No sound or sound is low • Adjust the volume settings of your monitor.

• Ensure that the computer sound card driver is properly installed and activated.

3.4 Supported operating modes

Resolution Frequency Horizontal Frequency (KHz) Vertical Frequency (Hz) Pixel (MHz)
640×480 31.5 60 25.18
640×480 35.0 67 30.24
640×480 37.9 72 31.50
640×480 37.5 75 31.50
720×400 31.5 70 28.32
800×600 35.16 56 36.00
800×600 37.9 60 40.00
800×600 48.1 72 66.75
800×600 46.9 75 49.50
832×624 49.7 75 57.28
1024×768 48.4 60 65.00
1024×768 56.5 70 75.00
1024×768 60.0 75 78.50
1152×864 67.5 75 108.00
1280×720 45 60 75.25
1280×768 47.78 60 79.50
1280×800 49.7 60 83.50
1280×960 60.0 60 108.00
1280×1024 63.4 60 108.00
1280×1024 79.97 75 135.00
1360×768 47.71 60 85.50
1366×768 47.71 60 85.50
1440×900 55.94 60 106.50
1600×1200 75.0 60 162.00
1680×1050 75.0 60 146.25
1920×1080 (Primary) 67.5 60 148.50

*Modes not listed in the table may not be supported. For optimal resolution, we recommend that you choose a mode listed in the table above.


 


 


 


 


 

Leave a comment

Your email address will not be published.