User Manual
HDMI True Matrix 4X4
4K@30Hz/IR/ RS232
Mode No : HDMX0015M1
INTRODUCITON
Picture 1.0 front panel showing
Picture 1.1 rear panel showing
Picture 1.2 IR panel showing
Firstly remove the plastic film in the rear board of the remote board.- The A, B, C, D signifies the A, B, C, D output.
- The 1, 2, 3, 4 signifies the 1, 2, 3, 4 input.
- Firstly press the left Letter Key, then press the right Number Key, the matched input signal and output port will be connected. For example: to press A key and then press number 4 key, the input 4 signal will be output to A port; to press B key, then press the number 3 key, the input 3 signal will be output to B port.
- To press the symbol “ALL” key at remote, it can set all output port to out the same input signal. First to press the symbol “ALL” key at remote, then select the input channel that you want. For example: to press the symbol “ALL” key, then press number 1 key to put the input channel 1 signal to all output port; to press the symbol “ALL” key at remote, then press the number 2 key, it can select input channel 2 signal to all output port.
- The plastic film is strongly advised to remove it when the remote is not used for long time.
Connection and operation:
*Connect according to the connection method in the above figure, source → display device → power
Spec:
| Mode No | ilDNIX0015N11 |
| Mode name | HDMI True Matrix 4X4 |
| Input channel | HDMI port x4 |
| Output channel | HDMI port x4 |
| RS232 interface | RS232 port x1 |
| RS232 serial communication | support |
| Resolution format | 480P/720P/1080PPIK02411z/4K030Ilz |
| Deep color | 8/10/12Bit |
| HDMI audio output format | 1.1)0,12. 0/DTS/DOLBY-AC3 |
| HDMI Input cable length | 2160P/AWG 26 .5m 1080P/AWG 26 -.10m |
| HDMI Output cable length | 2160P/AWG 26 —C.5m 1080P/AWG 26 :-C.10m |
| HDMI transmission bandwidth | 25-340MHz |
| HDMI transmission rate | 0.75-10.2Gbps |
| Power adapter specification | Input: AC 100-240V Output: DC 12V/1.5A |
| Max working current | 350mA |
| Working temperature range | 0 – +40ºC |
| Working humidity range | 5 to 85%RH ( No Condensation) |
| Storage temperature | -15 to 55ºC |
| Storage humidity | 5 -95%RH(No Condensation) |
| Size | 324x137x40. 05 (mm) |
| Weight | 1090g |
| Accessories | Manual, Power Adaptor, Remote |
RS232 Serial Port Operation Way
RS-232 Set-up
| Baud Rate: | 115200 bps |
| Data Bits: | 8 bits |
| Stop Bits: | 1 bit |
| Parity: | None |
| Flow Control: | None |
RS232 Serial Port Protocol
!XCOM# read the current status and return to the turn-off state; Current OUTAOUTB OUTCOUTD connected input channel port status,; OUTAOUTBOUTCOUTD will be turned off or not.
| Cannel (ASCII) | Description | Feedback(Retum) |
| !SW11# | Input I switches to OUT A | !RC 11# means switch succeeded |
| !SW I2# | Input 2 switches to OUT A | !RC I2# means switch succeeded |
| !SW I3# | Input 3 switches to OUT A | !RC I3# means switch succeeded |
| !SW 14# | Input 4 switches to OUT A | !RC14# means switch succeeded |
| !SW2I# | Input I switches to OUT B | !RC2I# means switch succeeded |
| !SW22# | Input 2 switches to OUT B | !RC22# means switch succeeded |
| !SW23# | Input 3 switches to OUT B | !RC23# means switch succeeded |
| !SW24# | Input 4 switches to OUT B | !RC24# means switch succeeded |
| !SW3I# | Input I switches to OUT C | !RC3 I# means switch succeeded |
| !SW32# | Input 2 switches to OUT C | !RC32# means switch succeeded |
| !SW33# | Input 3 switches to OUT C | !RC33# means switch succeeded |
| !SW34# | Input 4 switches to OUT C | !RC34# means switch succeeded |
| !SW4I# | Input I switches to OUT D | !RC4 I # means switch succeeded |
| !SW42# | Input 2 switches to OUT D | !RC42# means switch succeeded |
| !SW43# | Input 3 switches to OUT D | !RC43# means switch succeeded |
| !SW44# | Input 4 switches to OUT D | !RC44# means switch succeeded |
| !SWALLI# | Input I switch to all output ports | !RCALL I # means switch succeeded |
| !SWALL2# | Input 2 switch to all output ports | !RCALL2# means switch succeeded |
| !SWALL3# | Input 3 switch to all output ports | !RCALL3# means switch succeeded |
| !SWALL4# | Input 4 switch to all output Pons | !RCALL4# means switch succeeded |
| !SWFI# | Close OUT A | !RCF I # represent OUT A Off |
| !SWF2# | Close OUT B | !RCF2# represent OUT B Off |
| !SWF3# | Close OUT C | !RCF3# represent OUT C Off |
| !SWF4# | Close OUT D | !RCF4# represent OUT D Off |
| !SWO1# | Open OUT A | !RCO1# represent OUT A On |
| !SWO2# | Open OUT B | !RCO2# represent OUT B On |
| !SWO3# | Open OUT C | !RCO3# represent OUT C On |
| !SWO4# | Open OUT D | !RCO4# represent OUT D On |
| !SWP0# | Shut down | !RCP0# represent power off |
| !SWP1# | Power on | !RCP1# represent power on |
Documents / Resources
 | ASK HDMX0015M1 HDMI True Matrix 4x4 [pdf] User Manual HDMX0015M1 HDMI True Matrix 4x4, HDMX0015M1, HDMX0015M1 Matrix 4x4, HDMI True Matrix 4x4, HDMI Matrix 4x4, True Matrix 4x4, Matrix 4x4 |
