1. Introduction
This instruction manual provides detailed guidance for the installation, operation, maintenance, and troubleshooting of the Kenmore Dishwasher Drain Pump Solenoid, Model 10060-013. This component is designed to facilitate the proper drainage of water from your dishwasher. Please read this manual thoroughly before attempting any installation or repair to ensure safety and correct functionality.
2. Product Overview
The drain pump solenoid is a critical component in your dishwasher's drainage system. It controls the opening and closing of the drain valve, allowing water to be expelled from the dishwasher tub. This specific solenoid is rated for 120 Volts and includes all necessary components for installation.
Figure 2.1: Front view of the Dishwasher Drain Pump Solenoid, showing the electrical terminals and plunger housing.
3. Compatibility
This drain pump solenoid is compatible with various Kenmore dishwasher models. Please verify your dishwasher's model number against the list below to ensure compatibility before installation.
Compatible Kenmore Models:
- 363.16212100
- 363.16219100
- 363.16222100
- 363.16229100
- 363.15655892
- 363.15655893
- 363.15658891
- 363.15658892
- 363.15658893
- 363.15672000
- 363.15677000
- 363.15679000
- 363.16121100
- 363.16129100
- 363.16171100
- 363.16179100
- 363.15461794
- 363.15465793
- 363.15465794
- 363.15465795
- 363.15472000
- 363.15479000
- 363.15482000
- 363.15489000
- 363.15651891
- 363.15651892
- 363.15651893
4. Package Contents
Upon opening the package, ensure all the following components are present and undamaged:
- 1 x Dishwasher Drain Pump Solenoid (120 Volt coil)
- 1 x Plunger
- 1 x Cam
- 2 x Metal Mounting Brackets
- 3 x Screws
- 1 x Spring
- 1 x C-Clamp
- Installation Instructions (this manual)
Figure 4.1: Side view of the solenoid, illustrating the attached metal mounting bracket.
5. Safety Information
WARNING: Risk of electric shock and injury.
- Always disconnect power to the dishwasher at the circuit breaker before beginning any repair or installation.
- Wear appropriate personal protective equipment, such as gloves and safety glasses.
- If you are unsure about any step, consult a qualified appliance technician.
- Ensure all connections are secure and properly insulated after installation.
6. Installation Instructions
Follow these steps carefully to replace the dishwasher drain pump solenoid:
- Disconnect Power: Turn off the electrical power to the dishwasher at the main circuit breaker.
- Access the Drain Pump:
- Depending on your dishwasher model, you may need to pull the dishwasher out from under the counter or access the drain pump from the bottom.
- Lay down towels to catch any residual water.
- Locate the Old Solenoid: Identify the existing drain pump solenoid. It is typically attached to the drain pump assembly.
- Disconnect Wiring: Carefully disconnect the electrical wires from the old solenoid. Note their positions for re-connection.
- Remove Old Solenoid: Unscrew or unclip the old solenoid from its mounting.
- Install New Solenoid:
- Attach the new solenoid to the drain pump assembly using the provided screws and mounting brackets. Ensure the coil is slightly angled with the bent tab for a secure fit.
- Insert the plunger, cam, spring, and c-clamp as per the original configuration.
- Reconnect Wiring: Connect the electrical wires to the new solenoid. Ensure connections are tight and correct.
- Secure Dishwasher: Re-position the dishwasher and secure it if it was moved.
- Restore Power: Turn the electrical power back on at the circuit breaker.
- Test Functionality: Run a short wash cycle to verify that the dishwasher drains properly and there are no leaks.
Figure 6.1: An angled view of the solenoid, showing its complete structure and mounting points, useful for understanding installation.
7. Maintenance
The drain pump solenoid itself requires minimal maintenance. However, regular dishwasher maintenance can prolong its lifespan and prevent future drainage issues:
- Clean Filters: Regularly clean your dishwasher's filters to prevent food particles from clogging the drain pump.
- Inspect Drain Hose: Periodically check the drain hose for kinks or blockages.
- Avoid Overloading: Do not overload the dishwasher, as this can impede proper drainage.
8. Troubleshooting
If your dishwasher is experiencing drainage problems after solenoid replacement, consider the following:
| Problem | Possible Cause | Solution |
|---|---|---|
| Dishwasher not draining |
|
|
| Solenoid not activating |
|
|
9. Specifications
- Product Type: Dishwasher Drain Pump Solenoid
- Brand: Generic
- Model Number: 10060-013
- Voltage Rating: 120 Volts
- Dimensions: Approximately 1 x 1 x 1 inches (Product dimensions are often generalized; refer to actual part for precise measurements)
- Included Components: Solenoid, plunger, cam, 2 metal mounting brackets, 3 screws, spring, c-clamp.
10. Warranty and Support
For warranty information or technical support, please refer to the seller's policies or contact the seller directly through your purchase platform. It is recommended to retain your proof of purchase for any warranty claims.
For further assistance or if you are unsure about any repair steps, it is advisable to consult a certified appliance repair technician.
