Introduction
The Sweet Patina SP-600 Black Out Rust Preventative Gloss Black Coating is a high-solids, single-component underbody coating designed to permanently inhibit corrosion. This product protects various substrates from water, chemicals, salt, and other corrosive contaminants. It effectively stops rust when applied over a properly prepared rusted surface. The coating dries to a flexible, rock-hard finish that resists cracking, chipping, flaking, or peeling.
For surfaces exposed to direct sunlight, topcoating with an industrial finish is recommended for UV protection. This product is V.O.C. compliant in North America and is suitable for use on chassis and underbody components.
Safety Information
Always prioritize safety when working with chemical coatings. Read and understand all warnings on the product label before use.
- Ventilation: Use in a well-ventilated area. If applying indoors, ensure adequate airflow or use respiratory protection.
- Personal Protective Equipment (PPE): Wear appropriate PPE, including chemical-resistant gloves, eye protection (safety glasses or goggles), and protective clothing to prevent skin contact.
- Skin and Eye Contact: In case of skin contact, wash thoroughly with soap and water. For eye contact, flush immediately with plenty of water for at least 15 minutes and seek medical attention.
- Ingestion: Do not ingest. If swallowed, do not induce vomiting. Seek immediate medical attention.
- Flammability: Keep away from heat, sparks, open flames, and other ignition sources. Store in a cool, dry place.
- Disposal: Dispose of unused product and empty containers according to local regulations.
Setup and Surface Preparation
Proper surface preparation is crucial for optimal adhesion and performance of the coating. No primer is required for this product.
- Clean the Surface: Thoroughly clean the metal surface to be coated. Remove all loose rust, dirt, grease, oil, wax, and other contaminants. Use a degreaser or appropriate cleaning solution.
- Remove Loose Rust: For rusted surfaces, remove any loose or flaky rust using a wire brush, sandpaper, or abrasive pad. The coating can be applied over properly prepared rusted surfaces, but loose rust must be removed.
- Dry the Surface: Ensure the surface is completely dry before application. Moisture can compromise adhesion.
- Temperature: Apply in a temperature range recommended on the product label, typically between 50°F (10°C) and 90°F (32°C).
Image of the Sweet Patina SP-600 Black Out Rust Preventative Gloss Black coating in a 1-quart can, ready for application.
Operating and Application
The SP-600 coating can be applied using a brush, roller, or spray equipment.
- Mixing: Stir the product thoroughly before use to ensure uniform consistency. Do not shake vigorously, as this can introduce air bubbles.
- Application Methods:
- Brushing: Use a good quality natural bristle brush. Apply in thin, even coats.
- Rolling: Use a short-nap roller cover. Apply in thin, even coats.
- Spraying: For spray application, follow equipment manufacturer's recommendations for thinning (if necessary) and pressure settings. Ensure proper ventilation and respiratory protection.
- Coats: Apply one or two thin, even coats. Avoid applying excessively thick coats, as this can lead to longer drying times and potential adhesion issues.
- Drying Time: The coating dries to a hard, durable finish. Allow sufficient time between coats and before handling. Drying times can vary based on temperature, humidity, and film thickness. Refer to the product label for specific recoat and full cure times.
- Topcoating (Optional): If the coated surface will be exposed to direct sunlight, it is recommended to topcoat with an industrial finish for UV protection. Ensure the SP-600 coating is fully cured before applying a topcoat.
Maintenance
Once cured, the Sweet Patina SP-600 coating provides a durable, protective layer. Minimal maintenance is required.
- Cleaning: Clean the coated surface with mild soap and water as needed. Avoid harsh abrasive cleaners or solvents that could damage the finish.
- Inspection: Periodically inspect the coated areas for any signs of damage, such as deep scratches or impacts that might expose the underlying metal. Touch up any damaged areas promptly to maintain protection.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Poor Adhesion | Improper surface preparation (grease, oil, loose rust, moisture). | Ensure surface is thoroughly cleaned, dry, and free of contaminants. Remove all loose rust. |
| Uneven Finish / Brush Marks | Applying too thick, improper brush/roller, or incorrect thinning for spray. | Apply in thin, even coats. Use appropriate application tools. For spray, adjust settings and thinning as per manufacturer guidelines. |
| Slow Drying | High humidity, low temperature, or excessively thick coats. | Ensure adequate ventilation. Apply within recommended temperature range. Apply thinner coats. |
| Bubbles / Pinholes | Over-mixing, applying too quickly, or surface contaminants. | Stir gently, do not shake. Apply at a steady pace. Ensure surface is clean. |
Specifications
- Product Name: Sweet Patina SP-600 Black Out Rust Preventative Gloss Black Coating
- Model Number: SP-600
- Brand: Speedway Motors
- Manufacturer: Sweet Patina
- Color: Gloss Black
- Volume: 1 Quart (qt.)
- Item Weight: Approximately 3 pounds
- Product Dimensions: Approximately 4.9 x 4.2 x 4.2 inches
- VOC Compliance: V.O.C. compliant in North America
- Application Methods: Brush, Roll, Spray
- Features: Stops rust, protects from water, chemicals, salt; dries to a flexible, rock-hard finish; no primer required.
- UV Protection: Topcoating recommended for surfaces in direct sunlight.
Warranty Information
Specific warranty details for the Sweet Patina SP-600 coating are not provided in this manual. For information regarding product warranty, please refer to the product packaging or contact Speedway Motors directly. Keep your purchase receipt as proof of purchase.
Support and Contact
For technical assistance, product inquiries, or support, please contact Speedway Motors customer service. Refer to the Speedway Motors website or product packaging for the most current contact information.
Speedway Motors
www.speedwaymotors.com