Introduction
Thank you for choosing SOLFART LED Bathroom Vanity Lights. This manual provides essential information for the safe installation, operation, and maintenance of your S8568-3T and 6002-810mm light fixtures. Please read these instructions thoroughly before installation and retain them for future reference.
Safety Information
WARNING: Risk of electric shock. Disconnect power at the fuse box or circuit breaker before installation or servicing.
- All electrical connections must be in accordance with local codes, ordinances, and the National Electric Code (NEC).
- Consult a qualified electrician if you are unsure about the installation process.
- Ensure the fixture is properly grounded.
- Do not install this fixture in areas where it may be exposed to direct water spray or submersion. The IP44 rating indicates protection against splashing water.
- Do not attempt to modify the fixture. Integrated LED components are not user-replaceable.
- Handle the fixture with care to avoid damage to the LED components or glass/acrylic parts.
Package Contents
Verify that all components are present before beginning installation. If any parts are missing or damaged, contact customer service.
- SOLFART S8568-3T LED Vanity Light Fixture (1 unit)
- SOLFART 6002-810mm LED Vanity Light Fixture (1 unit)
- Mounting Hardware (screws, wire nuts, mounting bracket)
- Instruction Manual (this document)
Setup and Installation
These fixtures are designed for easy installation directly to a standard US junction box. Professional installation is recommended if you are not familiar with electrical wiring.
Tools Required (Not Included):
- Phillips head screwdriver
- Flathead screwdriver
- Wire strippers
- Electrical tape
- Safety glasses
Installation Steps:
- Turn off Power: Locate the circuit breaker or fuse box and turn off the power to the wall switch location. Verify power is off using a voltage tester.
- Remove Old Fixture (if applicable): Carefully remove any existing light fixture and its mounting hardware.
- Attach Mounting Bracket: Secure the provided mounting bracket to the junction box using the screws supplied with the junction box. Ensure the bracket is firmly attached.
- Make Electrical Connections:
- Connect the green or bare copper ground wire from the fixture to the ground wire from the junction box (usually bare copper or green). Secure with a wire nut.
- Connect the white wire from the fixture to the white (neutral) wire from the junction box. Secure with a wire nut.
- Connect the black wire from the fixture to the black (hot) wire from the junction box. Secure with a wire nut.
Ensure all wire nuts are tightly secured and no bare wire is exposed. Wrap connections with electrical tape for added security.
- Mount the Fixture: Carefully align the fixture with the mounting bracket and secure it using the provided screws. Ensure the fixture is flush against the wall and stable.
- Restore Power: Turn the power back on at the circuit breaker or fuse box. Test the light fixture.
Image: Product parameters and dimensions for the S8568-3T light fixture. It shows a length of 22 inches, a width of 4 inches, and a height of 4.3 inches. Electrical specifications include 24W power, 1920 lumens, CRI≥85, integrated LED chips, dimmable functionality, and up-and-down lighting.
Image: The SOLFART 6002-810mm LED bathroom vanity light, featuring a linear design with a brushed nickel base and a milky white integrated acrylic lampshade.
Operating Instructions
Once installed and power is restored, your SOLFART LED vanity lights are ready for use.
- Turning On/Off: Operate the light fixture using the standard wall switch connected to the circuit.
- Dimming Function (S8568-3T): The S8568-3T model is dimmable. To utilize this feature, ensure you have a compatible LED dimmer switch installed on your wall. Follow the dimmer switch manufacturer's instructions for operation.
- Light Direction (S8568-3T): The S8568-3T model provides both up and down lighting.
Image: A visual comparison showing the SOLFART 6002-810mm light fixture in both the OFF state (top) and the ON state (bottom), demonstrating its illumination.
Maintenance
These LED fixtures are designed for durability and low maintenance. Regular cleaning will help maintain their appearance.
- Cleaning: Before cleaning, ensure the power to the fixture is turned off at the circuit breaker. Use a soft, damp cloth to wipe the surface of the fixture. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish or acrylic components.
- LED Components: The integrated LED light source is designed for long life and does not require replacement. Do not attempt to open the fixture to access or replace LED components.
- Corrosion Resistance: The brushed nickel finish and moisture-proof design make these fixtures suitable for humid environments like bathrooms.
Image: Detailed view of the SOLFART 6002-810mm light fixture, highlighting the brushed nickel iron lamp body accessories and the high transparency milky white integrated acrylic lampshade. It also mentions a durable waterproof metal base.
Troubleshooting
If your light fixture is not functioning correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. |
|
|
| Light flickers or dims unexpectedly. |
|
|
| Fixture is damaged. |
|
|
Specifications
SOLFART S8568-3T LED Vanity Light:
- Model: S8568-3T
- Dimensions: Approximately 22 inches (Length) x 4 inches (Width) x 4.3 inches (Height)
- Power: 24W
- Luminous Flux: 1920 Lumens
- Color Rendering Index (CRI): ≥85
- Features: Integrated LED Chips, Dimmable, Up and Down Lighting
- Material: Brushed Nickel iron lamp body, Acrylic lampshade
SOLFART 6002-810mm LED Vanity Light:
- Model: 6002-810mm
- Dimensions: Approximately 810mm (31.9 inches) Length
- Material: Brushed Nickel iron lamp body, High transparency milky white integrated acrylic lampshade, Durable waterproof metal base
General Specifications (Both Models):
- Brand: SOLFART
- Style: Modern Bathroom Light Fixtures
- Waterproof Rating: IP44 (Protected against splashing water)
- Certifications: ETL/UL Certificated (power driver), CE / ROHS/ QCQ certificated (lamp fixtures parts)
- Installation: Suitable for US junction box standard
Warranty and Support
SOLFART provides a 2-year warranty for these LED bathroom vanity lights from the date of purchase.
If you encounter any issues or have questions regarding your product, please contact SOLFART customer service. We are committed to providing satisfactory solutions and will reply within 24 hours.
Customer Service Contact: Please refer to the contact information provided on your purchase receipt or the SOLFART official website.