1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your Samoser Refrigerator Water Inlet Valve. Please read these instructions carefully before proceeding with installation or any service to ensure proper function and safety. This valve is designed as an aftermarket replacement part for various refrigerator models from Kenmore, Whirlpool, KitchenAid, and Maytag.
2. Safety Information
WARNING: Risk of Electric Shock and Water Damage.
- Always disconnect power to the refrigerator before attempting any installation, repair, or maintenance.
- Turn off the water supply to the refrigerator before disconnecting any water lines.
- Ensure all water connections are secure and leak-free after installation to prevent water damage.
- If you are unsure about any step, consult a qualified technician.
3. Compatibility
This Samoser Refrigerator Water Inlet Valve is compatible with a wide range of refrigerator models from Kenmore, Whirlpool, KitchenAid, and Maytag. Please verify your refrigerator's model number against the list below to ensure compatibility. You can typically find your model number inside the refrigerator compartment or on a label on the back of the appliance.
Compatible Kenmore Models:
- 106.58599892, 106.58599893
- 106.58722800, 106.58722801, 106.58722802
- 106.58723800, 106.58723801, 106.58723802
- 106.58724800, 106.58724801, 106.58724802
- 106.58726800, 106.58726801, 106.58726802
- 106.58729800, 106.58729801, 106.58729802
- 106.58732800, 106.58732801, 106.58732802
- 106.58733800, 106.58733801, 106.58733802
- 106.58734800
- 596.72382410, 596.723824102, 596.72382411, 596.72382413
- 596.72383410, 596.723834102, 596.72383411, 596.72383412, 596.72383413
- 596.72389410, 596.72389411, 596.72389412, 596.72389413
This part is also an aftermarket replacement for various Whirlpool, KitchenAid, and Maytag refrigerator models.
4. Package Contents
Your package should contain the following items:
- 1x Refrigerator Water Inlet Solenoid Valve
- Mounting bracket (pre-attached or separate)
- Water line tubing (if included in specific kit)
- Quick-connect fitting (if included in specific kit)
Image 1: Overview of the Samoser Refrigerator Water Inlet Valve and included accessories. The valve features blue plastic housing with red and green solenoids, attached to a metal mounting bracket. A coiled white water line and a white quick-connect fitting are also visible.
Image 2: A different perspective of the water inlet valve, showing the blue plastic body, the red and green solenoid coils, and the metal mounting bracket. The white water line and quick-connect fitting are also present.
5. Installation / Setup
The following steps provide general guidance for replacing a refrigerator water inlet valve. Specific procedures may vary depending on your refrigerator model. Always refer to your refrigerator's service manual for detailed instructions.
- Prepare for Installation:
- Disconnect the refrigerator from the electrical power supply.
- Turn off the main water supply valve to your home or the specific valve supplying water to the refrigerator.
- Move the refrigerator away from the wall to access the back panel.
- Access the Old Valve:
- Remove the rear access panel of the refrigerator, typically secured with screws.
- Locate the existing water inlet valve. It will have water lines and electrical wires connected to it.
- Disconnect the Old Valve:
- Place a towel or shallow pan underneath the valve to catch any residual water.
- Disconnect the water lines from the old valve. This may involve unscrewing compression fittings or releasing quick-connect fittings.
- Carefully disconnect the electrical wiring harness from the solenoids on the old valve. Note the orientation of the wires if they are not color-coded or keyed.
- Unmount the old valve from its bracket or the refrigerator frame.
- Install the New Valve:
- Mount the new Samoser water inlet valve in the same location as the old one, ensuring it is securely fastened.
- Connect the electrical wiring harness to the solenoids on the new valve. Ensure connections are firm.
- Connect the water lines to the new valve. For quick-connect fittings, ensure the tubing is fully inserted until it seats firmly. For compression fittings, tighten them sufficiently to prevent leaks but avoid over-tightening.
- Test for Leaks and Functionality:
- Turn on the main water supply valve.
- Carefully check all connections on the new valve for any signs of leaks. Tighten connections slightly if necessary.
- Plug the refrigerator back into the electrical outlet.
- Dispense water from the refrigerator's dispenser and/or activate the ice maker to ensure water flows correctly through the new valve. Check for leaks again during operation.
- Final Steps:
- Once you confirm there are no leaks and the valve is functioning correctly, reattach the rear access panel.
- Push the refrigerator back into its original position.
6. Operation
The water inlet valve controls the flow of water into your refrigerator for the ice maker and water dispenser. When the ice maker calls for water or the dispenser lever is pressed, the refrigerator's control board sends an electrical signal to the valve's solenoids. This signal opens the valve, allowing water to flow from your home's water supply into the refrigerator. When the signal stops, the valve closes, stopping the water flow.
7. Maintenance
The Samoser Refrigerator Water Inlet Valve is designed for reliable operation with minimal maintenance. However, regular checks of your refrigerator's water system can help prevent issues:
- Inspect for Leaks: Periodically check the area around the water inlet valve and water lines for any signs of moisture or leaks.
- Water Filter Replacement: Ensure your refrigerator's water filter is replaced according to the manufacturer's recommendations to maintain water quality and prevent sediment buildup that could affect the valve.
- Clean Rear Access Area: When cleaning behind your refrigerator, gently wipe down the valve and surrounding components to remove dust and debris.
8. Troubleshooting
If you experience issues with your refrigerator's water dispenser or ice maker after installing the new valve, consider the following:
- No Water Dispensed / No Ice Production:
- Ensure the refrigerator is plugged in and receiving power.
- Verify the main water supply to the refrigerator is turned on.
- Check for kinks or blockages in the water supply line.
- Confirm electrical connections to the valve solenoids are secure.
- Ensure the refrigerator's water filter is not clogged and has been replaced recently.
- Water Leakage:
- Immediately turn off the water supply and disconnect power to the refrigerator.
- Inspect all water line connections at the valve for proper seating and tightness.
- Check for cracks or damage to the water lines or valve body.
- Slow Water Flow:
- Check water pressure from your home supply.
- Ensure the water filter is not clogged.
- Inspect water lines for partial kinks or obstructions.
If troubleshooting steps do not resolve the issue, contact customer support for further assistance.
9. Specifications
| Brand | Samoser |
| Part Type | Refrigerator Water Inlet Solenoid Valve |
| Compatible Appliance Brands | Kenmore, Whirlpool, KitchenAid, Maytag |
| Product Dimensions | Approximately 1 x 1 x 1 inches (Note: This refers to the valve body, actual dimensions may vary slightly with bracket/fittings) |
| Manufacturer | Samoser |
| ASIN | B0FVNDZFQD |
10. Warranty and Support
If you are unsure about the compatibility of this part with your specific refrigerator model or encounter any issues during installation or operation, please contact customer support for assistance. The seller aims to resolve problems within 24 hours.
For support inquiries, please refer to the contact information provided by your retailer or on the product packaging.