1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your MOUDOAUER Mini-SAS HD SFF-8643 to 4 SAS SFF-8482 Breakout Cable. Please read these instructions carefully before use to ensure optimal performance and prevent damage.
2. Product Overview
The MOUDOAUER Mini-SAS HD SFF-8643 to 4 SAS SFF-8482 Breakout Cable is designed to connect a Mini-SAS HD (SFF-8643) controller to four individual SAS/SATA hard drives (SFF-8482). This cable facilitates high-speed data transfer in server and storage systems.
- Connector 1: Internal Mini SAS HD SFF-8643 (36-pin)
- Connector 2: Four SAS SFF-8482 (29-pin) with power ports
- Function: Connects a SAS controller (Host) to four SAS/SATA disks (Target)
- Cable Length: 1 meter (approximately 3.3 feet)
- Color: Black and Blue
Image: Overview of the MOUDOAUER Mini-SAS HD to 4 SAS SFF-8482 breakout cable, showing both ends and the individual blue wires.
Image: The 1-meter cable coiled, highlighting its length and the SFF-8643 connector.
3. Setup Instructions
Follow these steps to correctly install your Mini-SAS HD breakout cable:
- Identify Host Port: Locate the Mini-SAS HD (SFF-8643) port on your motherboard or RAID controller. This port acts as the host.
- Connect Host End: Carefully connect the SFF-8643 end of the breakout cable to the corresponding port on your controller. Ensure a secure fit.
- Identify Target Drives: Prepare your SAS/SATA hard drives (HDDs) that feature SFF-8482 connectors. These drives will act as targets.
- Connect Target Ends: Connect each of the four SFF-8482 connectors from the breakout cable to the respective SAS/SATA HDDs. Ensure each connection is firm.
Important Note: This cable is designed for the Mini-SAS HD (SFF-8643) connector to be on the host (motherboard or RAID controller) side. If the SFF-8643 connector is on your backplane, this cable will not function correctly with that configuration.
Image: Detailed view of the SFF-8643 host connector and the four SFF-8482 target connectors, showing their pin configurations.
Image: The SFF-8643 connector positioned next to the four SFF-8482 connectors, illustrating the connection points.
4. Operating Instructions
Once the cable is securely connected as described in the Setup section, the system should recognize the connected hard drives. No further operational steps are required for the cable itself, as it is a passive component. Ensure your operating system and controller drivers are up-to-date for proper drive management.
5. Maintenance
To ensure the longevity and reliable performance of your cable:
- Keep the cable clean and free from dust and debris.
- Avoid sharp bends or kinks in the cable, as this can damage internal wiring.
- Do not expose the cable to extreme temperatures or moisture.
- When disconnecting, always grasp the connector housing, not the cable itself, to prevent strain on the connections.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Drives not detected | Incorrect host connection (SFF-8643 on backplane instead of controller). Loose cable connections. Faulty drive or controller. | Ensure SFF-8643 is connected to a motherboard or RAID controller. Verify all connections are secure. Test with known working drives/controller. |
| Intermittent connection | Damaged cable. Loose connections. | Inspect cable for visible damage. Replace if necessary. Reseat all connectors. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand | MOUDOAUER |
| Model | Mini-SAS HD SFF-8643 to 4 SAS SFF-8482 |
| Connector Type (Host) | Mini SAS HD SFF-8643 (36-pin) |
| Connector Type (Target) | 4 x SAS SFF-8482 (29-pin) with Power Port |
| Cable Length | 1 Meter (100cm) |
| Cable Color | Black & Blue |
| Item Weight | 3.03 ounces (approx. 86 grams) |
| Package Dimensions | 7.87 x 6.3 x 0.39 inches |
8. Warranty and Support
For warranty information or technical support, please refer to the documentation provided with your purchase or contact MOUDOAUER customer service through the retailer where the product was acquired. Please have your purchase details and product model number ready when contacting support.