AUTOONE JWA2 8000A Jump Box/Air Pump & JS02 6000A Jump Starter User Manual

1. Introduction

This manual provides detailed instructions for the safe and effective operation of your AUTOONE JWA2 8000A Jump Box/Air Pump and JS02 6000A Jump Starter. This versatile device combines a powerful jump starter with an integrated air compressor, a portable power bank, and an LED flashlight, designed for automotive emergencies and outdoor use. Please read this manual thoroughly before use and retain it for future reference.

The AUTOONE JWA2/JS02 unit combines an 8000A jump starter and a 150PSI air compressor for comprehensive vehicle emergency support.

2. Safety Information

Always observe the following safety precautions to prevent injury or damage to the device and property:

• Read all instructions before operating the device.
• Wear eye protection and protective clothing when jump starting a vehicle.
• Do not short circuit the jump starter clamps.
• Keep the device away from children.
• Do not expose the device to rain or moisture.
• Do not disassemble the device. Refer servicing to qualified personnel.
• Use the device in a well-ventilated area.
• Ensure proper polarity when connecting to a vehicle battery: red clamp to positive (+), black clamp to negative (-) or chassis ground.
• Do not overinflate tires. Always check the recommended tire pressure for your vehicle.
• Allow the air compressor to cool down after extended use to prevent overheating.

3. Product Overview

The AUTOONE JWA2/JS02 is equipped with multiple features to assist in various situations:

• Robust Jump-Starting Power: Up to 8000A peak current (JWA2) or 6000A (JS02) for 12V vehicles with all gas and up to 12L diesel engines.
• Built-in Force Start Intelligence: Automatically detects battery voltage and health, activating high-current output for weak or dead batteries.
• High-Performance Air Compressor: Inflates tires at 45 liters per minute, with a maximum pressure of 150PSI.
• 24000mAh Power Bank: Provides 18W MAX input/output for charging electronic devices.
• 600 Lumen LED Flashlight: Features high-beam, strobe, and SOS modes for illumination and emergencies.
• HD LCD Display: Shows real-time pressure, battery level, and inflation modes.
• Comprehensive Protection: Includes short-circuit, overcurrent, overvoltage, and IP67 dust/water resistance.

The integrated HD LCD display provides real-time information on battery level, tire pressure, and selected inflation modes.

4. Setup

4.1 Initial Charging

Before first use, fully charge the device. Connect the provided charging cable to the device's input port and a suitable power adapter (wall charger not included). The LCD display will indicate charging status. A full charge typically takes approximately 2.5 hours with an 18W fast charger.

The 24000mAh large-capacity unit can be fast-charged via its input port. Ensure the device is fully charged before use.

5. Operating Instructions

5.1 Jump Starting a Vehicle

1. Ensure the jump starter is sufficiently charged.
2. Connect the red clamp to the vehicle's positive (+) battery terminal.
3. Connect the black clamp to the vehicle's negative (-) battery terminal or a solid metal part of the engine block (chassis ground).
4. The device's "Built-in Force Start Intelligence" will automatically detect the battery status and initiate the jump-starting process.
5. Start the vehicle.
6. Once the vehicle starts, disconnect the black clamp first, then the red clamp.
7. Remove the jump starter from the vehicle battery.

Proper connection of the jump starter clamps to the vehicle battery terminals is crucial for safe operation. This unit supports 12V vehicles with all gas and up to 12L diesel engines.

5.2 Using the Air Compressor

1. Connect the air hose to the tire valve stem.
2. Power on the device.
3. Use the control buttons to select the desired inflation mode (car, motorcycle, bicycle, ball) and set the target pressure (PSI, BAR, KPA, Kg/cm²).
4. Press the start button to begin inflation. The compressor will automatically stop when the target pressure is reached.
5. Disconnect the air hose.

The integrated air compressor can inflate a pickup truck tire from 30PSI to 36PSI in approximately 2.5 minutes.

A single full charge can inflate up to 25 sedan tires (245/75 R17), 18 SUV tires (275/65 R18), or 6 pickup truck tires (315/70 R17).

5.3 Using as a Power Bank

1. Connect your electronic device to the USB output port(s) using a compatible charging cable.
2. The device will automatically begin charging.

The unit features 18W MAX input and 18W MAX output, allowing it to charge various electronic devices.

5.4 Using the LED Flashlight

Press the flashlight button to cycle through the available modes: High-beam, Strobe, SOS, and Off. The 600 Lumen LED flashlight provides illumination for roadside emergencies and other low-light situations.

6. Maintenance

• Charging: Recharge the device every 3-6 months, even if not used, to maintain battery health and prolong its lifespan.
• Storage: Store the device in a cool, dry place, away from direct sunlight, high temperatures, and excessive moisture.
• Cleaning: Wipe the device with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.

7. Troubleshooting

If you encounter issues with your AUTOONE jump starter, refer to the following common problems and solutions:

• Device not turning on: Check the battery level on the LCD display. Recharge the device if the battery is low.
• Vehicle not starting:
  • Ensure the jump starter clamps are correctly connected to the vehicle battery terminals (red to positive, black to negative/chassis ground).
  • Verify that the vehicle battery terminals are clean and free of corrosion.
  • If the vehicle battery is severely discharged, allow the "Force Start" function to operate for a few moments before attempting to start the vehicle.
• Air compressor not inflating:
  • Check that the air hose is securely connected to the tire valve stem.
  • Ensure the target pressure is set correctly and is higher than the current tire pressure.
• Device not charging external devices: Ensure the charging cables are properly connected to both the jump starter and the external device. Verify that the jump starter has sufficient charge.

8. Specifications

9. Warranty and Support

For warranty information or technical support, please contact AUTOONE customer service through the retailer where the product was purchased or visit the official AUTOONE website. Please have your model number (JWA2 or JS02) and purchase details available when contacting support.