Introduction
Thank you for choosing Sinocare Safe AQ Pro I Blood Glucose Test Strips. These strips are designed for use with the Sinocare Safe AQ Pro I Blood Glucose Meter to accurately measure blood glucose levels. This manual provides essential information for proper use, ensuring reliable results for effective diabetes management.
Compatibility: These blood glucose test strips are ONLY compatible with the Sinocare Safe AQ Pro I meter. This package includes 200 test strips; lancets are NOT included. Please verify your meter model before purchase.
Key Features:
- Silver-Carbon Accuracy: Features silver-carbon electrode technology for up to 10 times higher conductivity, ensuring stable signal transmission and reliable measurements.
- HCT Correction: Automatic hematocrit (HCT) correction technology (10%-70%) helps maintain accurate results under various usage conditions.
- Fast and Accurate Testing: Code-free strips require only 1 µL of blood and provide results in approximately 5 seconds, offering quick and comfortable blood glucose monitoring.
- Correct Usage: Test strips should be used within 180 seconds of removal from the vial to ensure maximum result accuracy.
Setup
Before performing a blood glucose test, ensure you have your Sinocare Safe AQ Pro I meter, a fresh test strip, a lancing device, and a lancet (not included with strips).
- Prepare the Test Strip: Remove one test strip from the vial. Immediately close the vial cap tightly to protect the remaining strips from moisture.
- Insert the Test Strip: With the meter turned off, insert the test strip into the test strip port of the Sinocare Safe AQ Pro I meter. Push it firmly until it clicks into place. The meter will automatically turn on and display a blood drop symbol, indicating it is ready for a blood sample.
This image demonstrates the correct method for inserting a Sinocare Safe AQ Pro I test strip into the blood glucose meter.
Operating Instructions
Follow these steps to perform a blood glucose test:
- Prepare Lancing Device: Load a new lancet into your lancing device according to its instructions.
- Obtain Blood Sample: Prick your fingertip with the lancing device to obtain a small drop of blood.
- Apply Blood Sample: Touch the tip of the test strip to the blood drop. The blood will be automatically drawn into the strip. Ensure the blood sample completely fills the reaction area of the strip.
- Read Results: The meter will display your blood glucose result in approximately 5 seconds.
This visual guide provides clear, numbered steps for using the Sinocare Safe AQ Pro I test strips, from insertion to obtaining a blood sample and viewing results.
Important Notes for Accurate Results:
- The blood glucose measurement process should ideally be completed within 3 minutes of removing the strip from the vial.
- After opening a new vial of test strips, all strips within that vial must be used within 6 months.
A Sinocare Safe AQ Pro I blood glucose meter is shown with a test strip inserted, displaying a reading of 104 mg/dL. This image also illustrates recommended storage conditions for the strips.
Maintenance
Proper storage and handling of your test strips are crucial for accurate results.
- Storage: Store test strips in their original vial with the cap tightly closed. Keep them in a cool, dry place between 10°C and 40°C (50°F and 104°F) and at a relative humidity of less than 90%. Do not store in direct sunlight or extreme temperatures.
- Expiration: Check the expiration date printed on the vial. Do not use expired test strips. Once opened, use the strips within 6 months.
- Disposal: Dispose of used test strips and lancets in a proper sharps container or according to local regulations for medical waste.
Troubleshooting
If you encounter issues during testing, consider the following:
- Error Message: If your meter displays an error message, refer to your Sinocare Safe AQ Pro I meter's user manual for specific error code explanations and solutions.
- Inaccurate Readings: Ensure the test strip is not expired, the vial cap was tightly closed after each use, and the test was completed within 180 seconds of removing the strip. Verify that the blood sample fully covered the reaction area.
- No Blood Drawn: Ensure the test strip is correctly inserted and that you have a sufficient blood sample.
- Meter Malfunction: If you suspect the meter is not functioning correctly, consult your meter's user manual or contact customer support.
Specifications
| Feature | Specification |
|---|---|
| Product Name | Sinocare Safe AQ Pro I Blood Glucose Test Strips |
| Model Number | Safe AQ Pro I 200WZ |
| Blood Sample Volume | 1 µL |
| Test Time | Approximately 5 seconds |
| Hematocrit (HCT) Range | 10% - 70% |
| Operating Temperature | 10°C - 40°C (50°F - 104°F) |
| Relative Humidity | <= 90% |
| Electrode Technology | Superconductive Silver-Carbon |
| Enzyme Type | FAD-GDH |
| Number of Strips per Pack | 200 (Lancets not included) |
| Manufacturer | Sinocare |
| Country of Origin | China |
This image provides a detailed diagram of the test strip's internal structure, showcasing the FAD-GDH glucose dehydrogenase and five-electrode system for high precision, stability, and anti-interference.
A diagram highlighting the advanced silver-carbon superconductor electrode technology of Sinocare Safe AQ Pro I test strips, emphasizing its 10x accuracy and enhanced interference immunity.
Warranty Information
Warranty information for Sinocare products, including test strips, is typically provided with the blood glucose meter or can be found on the official Sinocare website. Please refer to the documentation included with your Sinocare Safe AQ Pro I meter for specific warranty details.
Customer Support
For further assistance, technical support, or inquiries regarding your Sinocare Safe AQ Pro I Blood Glucose Test Strips, please visit the official Sinocare website or contact their customer service department. Contact details are usually available on the product packaging or the manufacturer's website.
