Introduction and Compatibility
This document provides instructions for the Richmat HJC26 MACB0032 C144980C250010 remote control, designed specifically for compatible adjustable bed base control boxes. This remote is not universal. To ensure compatibility, verify that your existing control box is a Richmat HJC26 MACB0032 C144980C250010 model. It is recommended to send a photo of your control box to the seller for confirmation before purchase.
The remote control requires 2 AAA batteries (not included).
Product Overview
Figure 1: Richmat HJC26 MACB0032 C144980C250010 Remote Control. This image displays the front view of the remote control, showing its buttons and general design. The remote is grey in color.
Setup and Pairing Instructions
Follow these steps to pair your new remote control with your adjustable bed base control box. Pairing must be completed within 15 seconds once initiated.
- Prepare the Bed Base: Unplug the adjustable bed base from the power outlet. Wait for at least 5 seconds, then plug it back in.
- Locate Control Box Reset Button: Locate the control box, typically found under the bed. Identify the "Learn" or "Reset Coding" button on the side of the control box.
- Initiate Pairing on Control Box: Double-click the "Reset" button on the control box twice. This will activate the pairing mode, indicated by a light on the control box.
- Initiate Pairing on Remote: On the remote control, simultaneously press and hold the "head up" button and the "foot up" button for 10 seconds.
- Confirm Pairing: Once you hear beeps from the bed base, it indicates that the remote control has successfully synced.
Important: If 15 seconds pass without successful pairing, the light on the control box will go out. You must unplug the power again and restart the process from Step 1.
Operating Instructions
After successful pairing, your remote control is ready for use. The remote typically features buttons for adjusting the head and foot sections of your adjustable bed base.
- Head Up/Down: Press the "head up" button to raise the head section of the bed. Press the "head down" button to lower it.
- Foot Up/Down: Press the "foot up" button to raise the foot section of the bed. Press the "foot down" button to lower it.
- Flat: A dedicated "flat" button (if present) will return the bed to a completely flat position.
- Memory Presets: Some remotes may include memory preset buttons (e.g., M1, M2) to save and recall preferred positions. Refer to your bed base manual for specific functions.
Ensure there are no obstructions under or around the bed base before operating to prevent damage or injury.
Maintenance
Battery Replacement
The remote control requires 2 AAA batteries. When the remote's performance degrades or it stops responding, replace the batteries.
- Locate the battery compartment cover on the back of the remote control.
- Slide or unclip the cover to open the compartment.
- Remove the old AAA batteries.
- Insert two new AAA batteries, ensuring correct polarity (+ and -).
- Replace the battery compartment cover.
Cleaning
To clean the remote control, use a soft, dry cloth. For stubborn dirt, lightly dampen the cloth with water or a mild, non-abrasive cleaner. Avoid using harsh chemicals or submerging the remote in liquid.
Troubleshooting
If your remote control is not functioning as expected, try the following troubleshooting steps:
- Remote Not Responding:
- Check if the batteries are correctly inserted and have sufficient charge. Replace them if necessary.
- Ensure there are no obstructions between the remote and the bed base's control box.
- Verify that the bed base is properly plugged into a working power outlet.
- Remote Not Paired:
- If the remote is not controlling the bed, it may have lost its pairing. Follow the "Setup and Pairing Instructions" section to re-pair the remote.
- Ensure you complete the pairing steps within the 15-second window.
- Intermittent Operation:
- Weak batteries can cause intermittent operation. Replace them.
- Ensure the control box is not covered or obstructed, which could interfere with the signal.
If these steps do not resolve the issue, contact the seller for further assistance.
Specifications
| Model Number | HJC26 MACB0032 C144980C250010 |
| Brand | Generic |
| Compatible Control Box | Richmat HJC26 MACB0032 C144980C250010 |
| Power Source | 2 x AAA Batteries (not included) |
| Color | Grey |
| Max Number of Supported Devices | 1 |
| Compatible Devices | Adjustable bed base |
Warranty and Support
Specific warranty information for this product is not provided in the available details. For any warranty-related inquiries or technical support, please contact the seller directly through your purchase platform.
When contacting support, please have your order number and a detailed description of the issue ready.
