PikSpiid 2000W Dual Motor Electric Bike Instruction Manual

1. Safety Information

Your safety is paramount. Please read this manual thoroughly before operating your PikSpiid Electric Bike. Failure to follow safety instructions may result in serious injury or property damage.

• Always wear a helmet and appropriate safety gear when riding.
• Ensure all components are securely fastened and brakes are functioning correctly before each ride.
• Familiarize yourself with local traffic laws and regulations regarding electric bikes.
• Do not ride under the influence of alcohol or drugs.
• Avoid riding in adverse weather conditions, such as heavy rain or snow, which can reduce traction and visibility.
• Maintain a safe speed and distance from other vehicles and pedestrians.
• Regularly inspect tires, brakes, and battery for wear and damage.
• The maximum load capacity for this electric bike is 330 lbs (150 kg). Do not exceed this limit.

2. Setup and Assembly

Your PikSpiid Electric Bike comes 90% pre-installed. Follow these steps to complete the assembly.

2.1 Package Contents

Upon unpacking, verify that all items are present:

• PikSpiid 2000W Dual Motor Electric Bike (main unit)
• Removable 48V 20.8Ah Lithium Battery
• Battery Charger
• Air Pump
• Instruction Manual (this document)
• Tool Kit

Image: Contents of the PikSpiid Electric Bike package, showing the bike, charger, pump, manual, and tool kit.

2.2 Assembly Steps

Refer to the following videos and instructions for detailed assembly guidance.

Key Assembly Points:

1. Handlebar Installation: Securely attach the handlebars to the stem. Ensure all bolts are tightened to the manufacturer's specifications.
2. Front Wheel Installation: Carefully align the front wheel with the fork. Ensure the brake rotor is correctly positioned within the caliper. Pay close attention to the order of nuts and washers, and ensure any gasket hooks are inserted into the small holes on the front fork. Tighten securely.
3. Mudguard Installation: Attach the front and rear mudguards using the provided screws and brackets.
4. Headlight Installation: Mount the LED headlight to the front of the bike. Connect the wiring harness, ensuring the indicating arrows on the connectors are aligned for a proper connection.
5. Display Screen Installation: Mount the LCD display screen to the handlebars. Connect the wiring harness, ensuring the indicating arrows on the connectors are aligned.
6. Pedal Installation: Distinguish between the left (L) and right (R) pedals. The left pedal typically has a reverse thread. Thread them into the crank arms and tighten firmly.
7. Tire Inflation: Inflate the 20x4 inch fat tires to the recommended pressure indicated on the tire sidewall.

3. Operating Instructions

Understand how to operate your PikSpiid Electric Bike for an optimal riding experience.

3.1 Powering On/Off

To power on the bike, press and hold the power button on the LCD display. Repeat to power off.

3.2 Riding Modes & Speed Levels

Your bike features 3 adjustable speed levels and 3+1 smart working modes:

• Dual-Drive Sport Mode: For maximum power and acceleration.
• Dual-Drive Race Mode: Optimized for high-speed performance.
• Single-Drive Eco Mode: Energy-efficient for extended range.
• Walk-Assist Mode: Provides low-speed assistance for walking alongside the bike.

You can flexibly switch between single/dual drive power based on road conditions. In dual-drive mode, twisting the throttle releases surging power, while single-drive mode is more energy-efficient. You can also turn off the electric assist and pedal like a regular bicycle.

Image: Illustration of the 1000W*2 peak brushless motor, 7-speed Shimano gears, 90 N.m max torque, and 35° gradeability.

3.3 LCD Display

The high-definition digital display shows real-time key information:

• Dual-drive mode indicator
• Left/right motor power
• Current speed
• Battery level
• Distance traveled

Image: Close-up of the handlebars, showing the LCD display, speed gear, 7-speed gear, throttle, shift button, headlights, horn, and turn signal light controls.

3.4 Lighting and Signals

The bike is equipped with 360° safety lighting:

• High-brightness LED headlight with expanded illumination range.
• Dual turn signals.
• Tail light.
• Brake light.
• Tire reflective strips.

Ensure all lights and signals are operational before riding, especially in low-light conditions.

4. Maintenance

Regular maintenance ensures the longevity and safe operation of your PikSpiid Electric Bike.

4.1 Battery Care

• Charge the 48V 20.8Ah removable battery using the provided charger. A full charge takes approximately 5-6 hours.
• The intelligent dual-drive Battery Management System (BMS) prevents overcharging, over-discharging, and short circuits. However, avoid leaving the battery fully discharged for extended periods.
• Store the battery in a cool, dry place when not in use.

Image: The removable 48V 20.8Ah lithium battery being charged, highlighting its capacity, charging time, UL certification, and BMS charge protection.

4.2 General Maintenance

• Tires: Regularly check the tire pressure of the 20x4 inch fat tires. Maintain pressure within the recommended range for optimal performance and safety.
• Brakes: Inspect the disc brakes for wear on pads and rotors. Ensure brake levers provide firm and responsive braking. Adjust or replace components as needed.
• Chain: Keep the chain clean and lubricated to ensure smooth gear changes and prevent wear.
• Fasteners: Periodically check all bolts, nuts, and quick-release levers to ensure they are securely tightened.
• Cleaning: Clean your bike with a damp cloth. Avoid using high-pressure water jets directly on electrical components.

5. Troubleshooting

This section provides solutions to common issues. For complex problems, contact customer support.

6. Specifications

Detailed technical specifications for your PikSpiid 2000W Dual Motor Electric Bike.

• Brand: PikSpiid
• Model: 2000W Dual Motor
• Bike Type: Electric Bike, Electric Dirt Bike, City Bicycle
• Motor: 1000W/2000W Peak Dual Brushless Motor
• Top Speed: Up to 45 KM/H (30 MPH)
• Battery: 48V 20.8Ah Removable Lithium Battery with BMS
• Range: 80-110 KM (50-68 miles) per charge (pedal assist), reduced in dual-drive mode.
• Charging Time: 5-6 hours
• Gearing: 7-Speed Shimano Gearing
• Tires: 20x4.0 inch All-Terrain Fat Tires (anti-puncture)
• Suspension: Full Suspension (Dual)
• Brakes: Disc Brakes
• Frame Material: Thickened Aluminum Alloy
• Max Load Capacity: 330 LBS (150 kg)
• Net Weight: 92 LBS (42 kg)
• Safety Features: High-brightness LED Headlight, Dual Turn Signals, Tail Light, Brake Light, Tire Reflective Strips
• Display: High-definition Digital LCD Display (shows mode, motor power, speed, battery, distance)
• Certifications: UL, FCC, GCC

Image: Dimension reference for the electric bike, including seat length (19.6 inch / 50 cm), seat height (32.6 inch / 83 cm), handlebar height (45 inch / 113 cm), total length (62 inch / 158 cm), net weight (92LB 42KG), and max load (330LBS).

7. Warranty and Support

Your PikSpiid Electric Bike is backed by quality assurance and customer support.

• Certifications: This adult electric bike has passed UL, FCC, and GCC certifications, ensuring compliance with safety and quality standards.
• Customer Service: If you encounter any problems during use, please feel free to contact us. We are committed to providing the best experience for every customer.

Image: Customer service details, including email addresses and a phone number for support and technical assistance.