Gemmy 6 FT Jason Voorhees Animatronic SS222218G Instruction Manual

Introduction

This manual provides essential instructions for the safe assembly, operation, and maintenance of your Gemmy 6 FT Jason Voorhees Animatronic (Model SS222218G). Please read this manual thoroughly before use and retain it for future reference.

Image: The Gemmy 6 FT Jason Voorhees Animatronic, showcasing its full height and detailed appearance, including the iconic hockey mask and machete.

Important Safety Information

• Indoor/Protected Outdoor Use Only: Do not expose this product to rain or snow. If used outdoors, it must be plugged into a Ground Fault Circuit Interrupter (GFCI) outlet and kept dry at all times. This animatronic is intended for indoor use or protected outdoor areas only.
• Electrical Safety: Ensure the power adapter and all electrical connections are secure and undamaged. Use only the provided power adapter. Do not overload electrical outlets.
• Placement: Position the animatronic on a stable, level surface to prevent tipping. Keep away from heat sources, open flames, and areas with excessive moisture.
• Children and Pets: Keep small children and pets away from the animatronic, especially during operation, to prevent injury from moving parts or electrical components.
• Moving Parts: The animatronic contains moving parts. Do not attempt to obstruct or interfere with the movement during operation.
• Cleaning: Disconnect power before cleaning. Use a soft, dry cloth. Do not use abrasive cleaners or immerse in water.

Package Contents

Please verify that all components are present before beginning assembly:

• Jason Voorhees Animatronic Figure (disassembled)
• Machete Prop
• Power Adapter (110 Volts)
• Assembly Hardware (screws, connectors, etc.)
• Instruction Manual (this document)

Setup Instructions

1. Unpack Components: Carefully remove all parts from the packaging. Lay them out on a clean, flat surface.
2. Assemble the Frame: Connect the metal frame components according to the diagrams provided in the separate assembly sheet (if included). Ensure all connections are secure.
3. Attach Clothing and Mask: Drape the clothing over the assembled frame. Secure the Jason Voorhees mask onto the head of the animatronic.
   

   Image: Detailed view of the animatronic's mask, highlighting its texture and features.

4. Insert Machete Prop: Carefully place the machete prop into the animatronic's hand. Ensure it is securely held.
   

   Image: The animatronic's hand gripping the machete prop, ready for display.

5. Position the Animatronic: Place the assembled animatronic in your desired location. Ensure it is on a stable, level surface and adheres to the safety guidelines for indoor or protected outdoor use.
   

   Image: Scale comparison of the animatronic, demonstrating its 6-foot height relative to an average person.

6. Connect Power: Locate the power input port, typically in the waist area at the back of the animatronic. Connect the power adapter to the animatronic, then plug the adapter into a standard 110-volt electrical outlet.

Operating Instructions

Once assembled and powered, the Gemmy Jason Voorhees Animatronic is designed for simple operation:

1. Power On: Ensure the power adapter is securely plugged into both the animatronic and a wall outlet. The animatronic should activate automatically or have a designated power switch (refer to product for exact switch location if present).
2. Activation: The animatronic features motion and sound effects. It is designed to activate its knife movement and sound effects when triggered (e.g., by motion sensor or continuous loop, depending on model variant).
3. Enjoy the Display: The animatronic will perform its programmed sequence, including knife movement and sound effects, creating an immersive Halloween display.
4. Power Off: To turn off the animatronic, simply unplug the power adapter from the wall outlet.

Maintenance

• Cleaning: Disconnect the power before cleaning. Use a soft, dry cloth to wipe down the animatronic. Do not use liquid cleaners, solvents, or abrasive materials, as these can damage the finish and electronic components.
• Storage: When not in use, disassemble the animatronic if necessary and store it in its original packaging or a protective container in a cool, dry place, away from direct sunlight and extreme temperatures.
• Inspection: Periodically inspect the power cord, adapter, and all connections for any signs of damage. Do not operate the animatronic if any components are damaged.

Troubleshooting

Specifications

Image: Product size chart detailing the animatronic's dimensions.

Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact Gemmy Industries directly through their official website. Keep your proof of purchase for any warranty claims.