1. Introduction
This manual provides detailed instructions for the installation and basic maintenance of the Generic replacement water pump, model Fricpart-100476, designed for compatibility with Kenmore Dishwasher Model 665.13463K900. Please read this manual thoroughly before beginning any installation or maintenance procedures to ensure safe and correct operation.
2. Safety Information
- Always disconnect power to the dishwasher before attempting any repairs or installations.
- Turn off the water supply to the dishwasher before beginning work.
- Wear appropriate personal protective equipment, such as gloves and eye protection.
- If you are unsure about any step, consult a qualified appliance technician.
- Keep small parts away from children.
3. Installation Instructions
This section outlines the general steps for replacing the dishwasher water pump. Specific disassembly and reassembly steps for your Kenmore 665.13463K900 model may vary slightly. Refer to your dishwasher's original service manual for detailed model-specific instructions.
3.1 Tools Required
- Screwdrivers (Phillips and Flathead)
- Pliers
- Adjustable wrench
- Towels or rags for water spills
- Bucket or shallow pan
3.2 Preparation
- Disconnect Power: Locate the circuit breaker for your dishwasher and turn off the power. Verify power is off by attempting to start the dishwasher.
- Turn Off Water Supply: Locate the water shut-off valve for the dishwasher, usually under the sink, and turn it off.
- Drain Water: If there is standing water in the dishwasher tub, manually drain it using a cup or sponge.
- Access Dishwasher: Carefully pull the dishwasher out from its cabinet enclosure to access the underside. You may need to disconnect the drain hose and water supply line if they are too short.
3.3 Removing the Old Water Pump
- Locate Pump: Identify the water pump assembly, typically located at the bottom of the dishwasher tub.
- Disconnect Wiring: Carefully disconnect any electrical wiring harnesses connected to the pump motor. Note their positions for reassembly.
- Disconnect Hoses: Loosen and remove the clamps securing the water hoses to the pump. Be prepared for residual water to spill; have towels and a bucket ready.
- Remove Mounting: Unfasten any screws, clips, or brackets holding the pump assembly in place.
- Extract Pump: Carefully remove the old water pump assembly from the dishwasher.
Figure 1: Generic Replacement Dishwasher Water Pump (Fricpart-100476). This image shows the complete water pump assembly, featuring a grey housing, a white central body, and a yellow impeller with multiple blades. This is the component you will be installing.
3.4 Installing the New Water Pump
- Position New Pump: Carefully place the new Fricpart-100476 water pump into the dishwasher, ensuring it aligns correctly with the mounting points.
- Secure Mounting: Fasten the pump with the screws, clips, or brackets removed earlier. Ensure it is securely in place.
- Reconnect Hoses: Attach the water hoses to the new pump and secure them with their clamps. Ensure a tight seal to prevent leaks.
- Reconnect Wiring: Reconnect all electrical wiring harnesses to the pump motor. Double-check that all connections are firm and correct.
3.5 Final Steps
- Reposition Dishwasher: Carefully slide the dishwasher back into its cabinet enclosure. Reconnect the drain hose and water supply line if they were disconnected.
- Restore Water Supply: Turn on the water shut-off valve. Check for any immediate leaks around the pump and hose connections.
- Restore Power: Turn on the circuit breaker for the dishwasher.
- Test Operation: Run a short wash cycle and carefully observe the dishwasher for proper operation and any leaks.
4. Maintenance
The water pump is a sealed unit and generally requires no routine maintenance. However, to ensure its longevity and the overall performance of your dishwasher:
- Regularly clean the dishwasher filter to prevent debris from reaching the pump.
- Avoid overloading the dishwasher, which can strain the pump.
- Use appropriate dishwasher detergents and rinse aids.
- Inspect hoses and connections periodically for signs of wear or leaks.
5. Troubleshooting
If you encounter issues after installing the new water pump, consider the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Dishwasher not draining | Clogged drain hose, faulty drain pump (if separate), or electrical connection issue. | Check drain hose for kinks or blockages. Verify electrical connections to the pump. If the issue persists, the drain pump (if separate from the wash pump) may need inspection. |
| Dishwasher not filling with water | Water supply valve off, clogged inlet screen, or faulty water inlet valve. | Ensure water supply is on. Check the inlet screen for debris. This issue is typically not related to the water pump itself. |
| Loud noise during wash cycle | Debris in pump impeller, incorrect installation, or a defective pump. | Disconnect power and water, then inspect the pump impeller for foreign objects. Recheck mounting for secure installation. If noise persists, the pump may be faulty. |
| Water leaks from pump area | Loose hose clamps, damaged gasket/seal, or cracked pump housing. | Tighten hose clamps. Inspect gaskets and seals for proper seating and damage. Ensure the pump housing is intact. |
If troubleshooting steps do not resolve the issue, it is recommended to contact a qualified appliance repair technician.
6. Specifications
- Part Type: Replacement Dishwasher Water Pump
- Compatible Dishwasher Model: Kenmore 665.13463K900
- Replacement Part Model: Fricpart-100476
- Manufacturer: Fricparts
- Color: Black/White (housing), Yellow (impeller)
- ASIN: B0FDH7FWCL
