beday IC-207 Solar Powered Dual Pump Drip Irrigation Kit User Manual

Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your beday IC-207 Solar Powered Dual Pump Drip Irrigation Kit. This automatic watering system is designed to efficiently water your plants in gardens, patios, and balconies, ensuring consistent moisture for healthy growth.

Safety Information

Important Safety Precautions:

• Ensure the anti-siphon part is positioned above the water level in the container. Do not submerge it.
• Manual mode operation will not affect the timing mode.
• For outdoor use, place the system in a location protected from extreme weather conditions.

Package Contents

Verify that all components are present before beginning installation:

• Watering System Dual-Pump (1 unit)
• Water Pipe 10m (33ft) x2
• Drippers x20
• T-Connectors x20
• Filter Head x2
• Anti-siphon Accessory x2
• Solar Panel with Stand x1
• Syringe x1
• USB-C Charging Cable x1
• User Manual x1

Image: All components included in the beday IC-207 Drip Irrigation Kit.

Setup and Installation

Follow these steps to set up your drip irrigation system:

1. Cut Tubing: Cut the provided tubing into appropriate lengths based on the number of plants you have and their spacing. Ensure enough length to reach each plant from the main unit and the water source.
   

   Image: Cutting the irrigation tubing to desired lengths.

2. Connect Drippers: Connect the tubing to the drippers using the T-connectors. Insert the drippers into the soil near the base of each plant. Ensure the anti-siphon device and the main watering unit are positioned higher than the water source to prevent backflow.
   

   Image: Connecting tubing to drippers with T-connectors.

   

   Image: Placing a dripper into a potted plant.

3. Attach Filter Head: Attach the tubing to the filter head, then connect the filter head to the watering system's inlet. Place the filter head into your water reservoir (e.g., a bucket of water).
   

   Image: Connecting the filter head to the tubing and main unit.

4. Position Solar Panel: Place the solar panel in a location that receives ample sunlight to charge the internal battery.
5. Final Connections: Ensure all tubing connections are secure. The system is now ready for programming.

Operating Instructions

The beday IC-207 features a user-friendly interface for setting watering schedules. The display shows the current time and next watering times for Pump A and Pump B.

Image: Display showing separate watering schedules for Pump A and Pump B.

1. Set Local Time

1. Press the SET button. The hour digits under "CLOCK" will start flashing.
2. Rotate the OK knob to select the hour.
3. Press the OK knob vertically to confirm.
4. The minute digits will start flashing.
5. Rotate the OK knob to select the minutes.
6. Press the OK knob again to confirm.

Note: Time is displayed in 24-hour format.

Image: Setting the local time on the watering system.

2. Set Watering Schedule for Pump A or B

1. Press the A/B button. The selected pump (A or B) will start flashing on the screen.
2. Press the SET button. The hour digits for the first watering time will flash.
3. Rotate the OK knob to select the hour.
4. Press the OK knob to confirm.
5. The minute digits will flash.
6. Rotate the OK knob to set the minutes.
7. Press the OK knob again to confirm.

Image: Setting the first watering time for a pump.

3. Set Watering Duration

1. The screen will display "Watering", and the watering duration digits will flash.
2. Rotate the OK knob to select the desired watering time (e.g., 10s, 20s, 30s, 40s, 50s, 1-30 minutes).
3. Press the OK knob to confirm.

Image: Setting the watering duration.

4. Set Watering Interval

1. The screen will display "Interval", and the interval digits will flash.
2. Rotate the OK knob to choose the interval between watering sessions (e.g., 1-12 hours / 1-15 days).
3. Press the OK knob to confirm.
4. Repeat the above process to set the schedule for the other pump (A or B).

Image: Setting the watering interval.

5. How to Turn Off One Pump

1. Short press the A/B button once, then long press the pause button for 1.5 seconds to turn off pump A. The display will show "-----".
2. Press the A/B button twice, then press and hold the pause button for 1.5 seconds to turn off pump B. The display will show "-----".

Note: Repeat the above operation again to exit the pump shutdown mode.

Image: Display indicating a pump is turned off.

Maintenance

• Filter Cleaning: Regularly check and clean the filter heads to prevent clogging and ensure optimal water flow. Rinse them under running water to remove debris.
• Tubing Inspection: Periodically inspect the tubing for kinks, leaks, or damage. Replace any damaged sections to maintain system efficiency.
• Dripper Check: Ensure drippers are not clogged and are delivering water consistently to the plant roots. Clean or replace as needed.
• Water Reservoir: Keep the water reservoir clean to prevent algae growth and sediment buildup, which can clog the system.
• Winter Storage: If using outdoors in cold climates, drain the system completely and store the main unit indoors to prevent freezing damage.

Troubleshooting

Product Specifications

Warranty and Support

The beday IC-207 Solar Powered Dual Pump Drip Irrigation Kit comes with a standard manufacturer's warranty. For warranty claims, technical support, or any questions regarding your product, please contact beday customer service through the retailer where you purchased the product or visit the official beday website for contact information.