Instruction Manual

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your new Generic replacement water drain pump with flapper. This part is designed to be compatible with Kenmore Washer Model 110.84762300. Please read these instructions carefully before proceeding with installation to ensure proper function and safety.

2. Safety Information

• Disconnect Power: Always unplug the washer from the electrical outlet before attempting any repairs or maintenance. Failure to do so can result in electric shock or serious injury.
• Water Hazard: Be aware that water may be present in the washer and drain lines. Have towels and a bucket ready to catch any spills.
• Professional Installation: If you are not comfortable performing appliance repairs, it is recommended to seek assistance from a qualified technician.
• Wear Protective Gear: Wear gloves and eye protection to prevent injury from sharp edges or chemical exposure.

3. Compatibility Verification

This replacement part is specifically designed for Kenmore Washer Model 110.84762300. Appliance parts can appear similar across different models. To ensure correct fitment and function, verify your washer's model number before installation. The model number is typically located on a label inside the washer door, on the back of the washer, or on the control panel.

The part number for this replacement drain pump is FRIC-PL-APP-TP-22052025-017333.

4. Package Contents

• 1 x Generic Replacement Water Drain Pump with Flapper (Part Number: FRIC-PL-APP-TP-22052025-017333)

Image: The Generic replacement water drain pump with flapper, showing its white plastic housing, motor shaft, and two hose connections. The flapper mechanism is visible in one of the outlets.

5. Setup and Installation

The following steps provide a general guide for replacing a washer drain pump. Specific procedures may vary depending on your exact Kenmore washer model. Always refer to your washer's original service manual for detailed, model-specific instructions.

1. Prepare the Washer:
   • Disconnect the washer from the electrical power supply.
   • Turn off the water supply to the washer.
   • Disconnect the hot and cold water inlet hoses from the back of the washer.
   • Disconnect the drain hose from the standpipe or utility sink.
   • Carefully move the washer away from the wall to access the rear or bottom.
   • Tilt the washer back and prop it securely, or lay it on its front/back as required by your model to access the pump. Place towels and a shallow pan underneath to catch residual water.
2. Locate the Drain Pump: The drain pump is typically located at the bottom of the washer, often near the motor.
3. Remove the Old Pump:
   • Loosen the clamps securing the hoses to the old drain pump and carefully remove the hoses. Be prepared for water to drain out.
   • Disconnect any electrical wiring harnesses connected to the pump. Note their orientation for reinstallation.
   • Unscrew or unclip the old pump from its mounting bracket.
4. Install the New Pump:
   • Position the new drain pump (Part Number: FRIC-PL-APP-TP-22052025-017333) onto the mounting bracket and secure it with screws or clips.
   • Reconnect the electrical wiring harnesses to the new pump. Ensure connections are secure.
   • Attach the hoses to the new pump and secure them with the clamps. Ensure hoses are fully seated and clamps are tight to prevent leaks.
5. Reassemble and Test:
   • Return the washer to its upright position.
   • Reconnect the drain hose, water inlet hoses, and plug the washer back into the electrical outlet.
   • Turn on the water supply.
   • Run a short drain/spin cycle to check for leaks and proper pump operation.

6. Operating Principles

The water drain pump is a critical component of your washing machine's drainage system. During the wash and rinse cycles, the pump activates to remove water from the wash tub, directing it through the drain hose. The integrated flapper mechanism helps prevent water from flowing back into the tub after it has been pumped out, ensuring efficient drainage and preventing re-contamination of clothes.

7. Maintenance

While the drain pump itself requires minimal maintenance, regular checks of the surrounding components can prolong its life and ensure efficient operation:

• Check for Obstructions: Periodically inspect the drain hose and the pump's inlet for lint, small items (coins, buttons), or other debris that could clog the pump or hoses. Many washers have a small filter or trap accessible from the front or bottom that should be cleaned regularly.
• Inspect Hoses: Check the drain hoses for kinks, cracks, or blockages that could impede water flow.
• Listen for Unusual Noises: A properly functioning pump should operate smoothly. Unusual grinding, humming, or rattling noises may indicate a problem with the pump or an obstruction.

8. Troubleshooting

If your washer is experiencing drainage issues after installing the new pump, consider the following:

• Washer Not Draining:
  • Ensure the drain hose is not kinked or blocked.
  • Check the washer's internal filter/trap for obstructions.
  • Verify electrical connections to the pump are secure.
  • Confirm the pump is receiving power during the drain cycle (this may require a multimeter and professional knowledge).
• Leaking Water:
  • Check all hose connections to the pump for tightness. Ensure clamps are properly secured.
  • Inspect hoses for cracks or damage.
  • Ensure the pump is correctly seated and mounted.
• Unusual Noises:
  • Disconnect power and inspect the pump impeller for any foreign objects (e.g., coins, buttons) that may be caught.
  • Ensure the pump is securely mounted and not vibrating against other components.

If troubleshooting steps do not resolve the issue, consult a qualified appliance repair technician.

9. Specifications

10. Warranty and Support

This product is a replacement part manufactured by Fricparts. For warranty information or technical support regarding this specific replacement drain pump, please refer to the seller or manufacturer's documentation provided at the time of purchase. The warranty for this replacement part is separate from any warranty covering your original Kenmore washer.

For further assistance, please contact the seller directly through your purchase platform.