1. Product Overview
This instruction manual provides guidance for the installation and maintenance of the replacement agitator cam dogs kit for Amana NTW4516FW3 washing machines. This kit is designed to restore proper agitator function by replacing worn or damaged cam dogs, which are crucial components for the agitator's one-way clutch mechanism.
2. Package Contents
The kit includes the following components:
Image 1: Complete kit showing the agitator cam dogs, agitator drive block, agitator base, and related seals/washers.
- Agitator Cam Dogs (4x): Small, clear plastic components responsible for engaging the agitator.
- Agitator Drive Block: The main white plastic component that houses the cam dogs and connects to the agitator shaft.
- Agitator Base/Washer Support: A white plastic ring that sits at the base of the agitator.
- Agitator Clutch Band/Ring: A black plastic ring that works with the cam dogs.
- Rubber O-ring/Seal: A large black rubber ring for sealing.
- Small Rubber Washer: A small black rubber washer.
3. Compatibility
This replacement kit is specifically designed for the Amana washing machine model NTW4516FW3. Please verify your washing machine's model number before proceeding with installation to ensure proper fit and function. Appliance parts can appear similar; confirming the model number is essential.
4. Installation Instructions
Safety First: Before attempting any repair, always disconnect the washing machine from its power source by unplugging it from the wall outlet. Turn off the water supply to the washer.
Replacing agitator cam dogs typically involves disassembling the agitator. If you are not comfortable performing this repair, it is recommended to consult a qualified appliance technician.
General Steps:
- Access the Agitator: Open the washer lid. Depending on your specific agitator design, you may need to remove a cap or fabric softener dispenser from the top of the agitator to expose a bolt.
- Remove the Agitator Bolt: Use an appropriate socket wrench to loosen and remove the bolt securing the agitator.
- Remove the Agitator: Carefully pull the agitator straight up and out of the washer tub. It may require some force if it's stuck.
- Disassemble the Agitator (if necessary): Some agitators are two-piece designs. If yours is, separate the upper and lower sections to access the cam dogs.
- Replace Cam Dogs: Locate the old cam dogs within the agitator drive block. Remove them and insert the new cam dogs from the kit into their respective slots. Ensure they are seated correctly.
- Reassemble Agitator: Reassemble the agitator components, ensuring all parts are correctly aligned.
- Reinstall Agitator: Place the agitator back onto the washer's agitator shaft, aligning the splines. Push down firmly.
- Secure Agitator: Reinstall and tighten the agitator bolt. Do not overtighten.
- Test: Reconnect power and water supply. Run a short cycle to ensure the agitator functions correctly.
Refer to your washing machine's specific service manual for detailed, model-specific instructions and diagrams.
5. Maintenance
Regular maintenance can extend the life of your washing machine components. While cam dogs are wear-and-tear parts, ensuring the agitator is not overloaded and that foreign objects do not interfere with its movement can help prevent premature wear.
- Avoid overloading the washer, as this can strain the agitator mechanism.
- Periodically check the agitator for any signs of unusual movement or noise, which may indicate worn parts.
6. Troubleshooting
If your agitator is not moving or is only moving in one direction after replacing the cam dogs, consider the following:
- Incorrect Installation: Double-check that the cam dogs are seated correctly and that the agitator is fully engaged with the transmission shaft.
- Damaged Agitator Splines: Inspect the splines inside the agitator and on the transmission shaft for wear or damage. If these are worn, the agitator may not engage properly.
- Other Component Failure: If the cam dogs are correctly installed and the agitator still malfunctions, the issue might lie with other internal components of the washer's transmission or motor. Professional diagnosis may be required.
7. Specifications
- Part Type: Washer Agitator Cam Dogs Kit
- Compatible Washer Model: Amana NTW4516FW3
- Manufacturer: Fricparts
- Part Number: FRIC-PL-APP-TP-22052025-000188
- Item Package Quantity: 1 kit
- Number Of Pieces: Multiple (as shown in package contents)
- Color: Black/White (components vary)
8. Warranty and Support
For information regarding warranty coverage or technical support for this replacement part, please refer to the seller or manufacturer's documentation provided at the time of purchase. Keep your purchase receipt for warranty claims.
