Chaoos 200EP Tone Generator Kit: Wire Tracer Circuit Tester User Manual

1. Introduction

The Chaoos 200EP Tone Generator Kit is a comprehensive tool designed for efficient network cable testing and troubleshooting. This kit includes an inductive amplifier probe and a tone generator, enabling users to trace and identify cables without causing damage. It is suitable for IT professionals, technicians, and DIY enthusiasts for locating and testing RJ11 connections, network cables, and various other wiring configurations. The ergonomic design and clear audio signals facilitate precise wire location and identification.

2. Product Components

The Chaoos 200EP Tone Generator Kit includes the following items:

• 1 * Tone Generator (Emitter)
• 1 * RJ11 Wire Tracker Probe (Receiver)
• All necessary accessories for connection (e.g., alligator clips, RJ11 connector)
• Durable carrying case

Image 2.1: Overview of the Chaoos 200EP Tone Generator Kit components, including the gray Wire Tracker emitter, the gray inductive amplifier receiver, the yellow Cable Tracker emitter, the yellow inductive amplifier receiver, and various connecting cables and clips.

Image 2.2: Detailed view of the Wire Tracker Emitter and Receiver. The emitter features an alligator clip, registered Jack-11, and a switch for TONE/OFF/CONTINUITY/POLARITY. The receiver shows the horn, battery compartment, LED, ON/OFF button, and carbon fiber tip.

3. Setup

1. Battery Installation: The tone generator kit requires two 9V batteries (NOT INCLUDED). Open the battery compartment on both the emitter and receiver units and insert the batteries, ensuring correct polarity.
2. Connect the Emitter:
   • For bare wires: Use the alligator clips to connect the emitter to the wire pair you wish to trace. Connect one clip to one conductor and the other clip to the second conductor or ground.
   • For RJ11 connections: Plug the RJ11 connector from the emitter into the RJ11 port of the cable or device.
   • For network cables: Use the RJ45 connector (if applicable, or alligator clips) to connect to the network cable.
3. Power On: Set the emitter switch to the "TONE" position to begin generating a signal.

Image 3.1: Close-up view of the various connectors, including angled alligator clips for easier access to wire pairs, and an RJ-11 connector suitable for telephone outlets. Also shows the battery connections within the unit.

4. Operating Instructions

The tone generator and probe kit is primarily used to measure non-energized cables or low voltage conditions below 24V.

4.1 Wire Tracing

1. Ensure the emitter is connected to the target wire and set to "TONE" mode.
2. Turn on the receiver by pressing and holding the spring-loaded ON/OFF button.
3. Adjust the volume dial on the receiver to a comfortable level.
4. Move the carbon fiber tip of the receiver along the suspected path of the wire. The receiver will emit an audible tone, which will be loudest when directly over the traced wire.
5. Use the varying intensity of the tone to pinpoint the exact location of the wire and track its path.

Image 4.1: Demonstrates the inductive amplifier receiver being used to accurately track the location of breakpoints in wires. The insulation probe helps avoid conductor short circuits.

4.2 Continuity Testing

1. Connect the emitter's test leads (alligator clips) to the two ends of the wire or circuit you want to test for continuity.
2. Set the emitter switch to "CONTINUITY".
3. If there is continuity, the LED on the emitter will illuminate, indicating a complete circuit.

4.3 Polarity Checking (for Telephone Lines)

1. Connect the emitter to the telephone line using the RJ11 connector or alligator clips.
2. Set the emitter switch to "POLARITY".
3. The emitter will indicate the polarity of the telephone line.

Image 4.2: Illustrates the emitter connected to an RJ11 wall jack, demonstrating its capability to identify three states of telephone lines: Clear, Busy, and Ringing.

Image 4.3: Highlights the multifunctional capabilities of the tester, including receiving audio signals on cables/wires, detecting continuity, and sending continuous or variable tone generator signals.

5. Maintenance

• Cleaning: Wipe the units with a dry, soft cloth. Do not use abrasive cleaners or solvents.
• Battery Replacement: Replace batteries when the indicator light dims or the tone weakens. Always use fresh 9V batteries.
• Storage: Store the kit in its durable carrying case in a cool, dry place away from direct sunlight and extreme temperatures.
• Safety: Always ensure the kit is used on non-energized cables or low voltage conditions below 24V to prevent damage to the device and ensure user safety.

6. Troubleshooting

• No Tone from Receiver:
  • Check if the emitter is powered on and set to "TONE" mode.
  • Ensure the emitter is correctly connected to the wire.
  • Verify that the receiver has fresh batteries and is turned on.
  • Adjust the receiver's volume dial.
  • Confirm the cable is non-energized or below 24V.
• Weak or Intermittent Tone:
  • Replace batteries in both units.
  • Ensure good contact between the emitter and the wire.
  • Minimize interference from other electrical devices or strong electromagnetic fields.
• Continuity LED Not Lighting Up:
  • Check battery levels.
  • Ensure proper connection of test leads.
  • The circuit may have an open break.

7. Specifications

8. Warranty and Support

Chaoos offers dedicated after-sales service for this tone generator kit. If you have any questions or encounter issues within 365 days of purchase, please contact us via email or through the QA section on the product page. Our service team is committed to providing a response within 12 hours to ensure customer satisfaction.

For further assistance, please refer to the contact information provided with your purchase or visit the official Chaoos store on Amazon.