Glintique 6ED1055-1MA00-0BA0 Simatic LOGO! AM2 Expansion Module User Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of the Glintique 6ED1055-1MA00-0BA0 Simatic LOGO! AM2 Expansion Module. Please read this manual thoroughly before installation, operation, or maintenance to ensure proper use and to prevent damage to the device or injury to personnel.

The 6ED1055-1MA00-0BA0 is designed to expand the capabilities of your existing PLC system, specifically compatible with Simatic LOGO! AM2. It offers enhanced functionality for programmable logic modules.

2. Safety Instructions

WARNING: Failure to observe these safety instructions may result in serious injury or property damage.

• Ensure all power is disconnected before installation, wiring, or maintenance.
• Installation and wiring must be performed by qualified personnel only.
• Do not operate the module in environments exceeding its specified operating conditions (temperature, humidity, etc.).
• Protect the module from moisture, dust, and corrosive substances.
• Verify all connections are secure and correct before applying power.

3. Product Overview

The Glintique 6ED1055-1MA00-0BA0 is an expansion module designed to seamlessly integrate with Simatic LOGO! AM2 systems. It provides additional input/output capabilities to enhance the control and monitoring functions of your programmable logic controller.

Figure 1: Front view of the Glintique 6ED1055-1MA00-0BA0 Simatic LOGO! AM2 Expansion Module. This image shows the module's compact design, terminal blocks for power and inputs, and the "AM2" and "RUN/STOP" indicators. The model number "6ED1055-1MA00-0BA0" is visible on the front panel.

3.1 Key Features

• Compatibility with Simatic LOGO! AM2.
• Easy installation and integration.
• Durable and reliable construction.
• Expands PLC system capabilities.

3.2 Components

The module consists of:

• Power Terminals (L+, M): For connecting the DC 12/24V power supply.
• Input Terminals (I1, M1, U1, I2, M2, U2): For connecting analog inputs (0-10V or 0-20mA).
• DC 12/24V Selector Switch: To select the operating voltage.
• RUN/STOP Indicator: LED to show the module's operational status.
• Mounting Clips: For DIN rail mounting.

4. Setup and Installation

4.1 Mounting

1. Ensure the power supply to the main LOGO! module and any connected devices is OFF.
2. Attach the expansion module to a standard DIN rail by hooking the top edge onto the rail and pressing down until it clicks into place.
3. Ensure the module is securely fastened.

4.2 Wiring

CAUTION: Incorrect wiring can damage the module and connected equipment.

1. Power Supply: Connect the DC 12/24V power supply to the L+ and M terminals. Observe polarity.
2. Analog Inputs: Connect your analog sensors or devices to the input terminals (I1, M1, U1, I2, M2, U2) as required. Refer to the specific sensor documentation for wiring details. The module supports 0-10V or 0-20mA inputs.
3. Interconnection: Connect the expansion module to the main LOGO! module using the appropriate communication cable or bus connector (not included, typically part of the LOGO! system).

4.3 Initial Power-Up

1. Double-check all wiring connections for correctness and security.
2. Set the DC 12/24V selector switch to the appropriate voltage matching your power supply.
3. Apply power to the main LOGO! system. The RUN/STOP indicator on the AM2 module should illuminate, indicating power and operational status.

5. Operating Instructions

Once installed and powered, the 6ED1055-1MA00-0BA0 module operates as an extension of your Simatic LOGO! AM2 system. Its functionality is controlled and configured through the LOGO! software environment.

5.1 Analog Input Configuration

• Refer to the Simatic LOGO! programming manual for detailed instructions on configuring analog inputs.
• The module provides two analog inputs, configurable for either 0-10V or 0-20mA signals.
• Within the LOGO! software, you will assign these physical inputs to specific functions within your control program.

5.2 Status Indicators

• The RUN/STOP indicator provides a visual cue of the module's operational state.
• A steady light typically indicates normal operation (RUN mode).
• Refer to the main LOGO! manual for specific indicator behaviors and troubleshooting.

6. Maintenance

The 6ED1055-1MA00-0BA0 module is designed for minimal maintenance. Regular checks can help ensure long-term reliability.

6.1 Cleaning

• Ensure power is disconnected before cleaning.
• Wipe the exterior of the module with a soft, dry, lint-free cloth.
• Do not use liquid cleaners, solvents, or abrasive materials.

6.2 Inspection

• Periodically inspect wiring connections for tightness and signs of corrosion.
• Check for any visible damage to the module casing or terminals.
• Ensure adequate ventilation around the module to prevent overheating.

7. Troubleshooting

This section provides solutions to common issues you might encounter with the 6ED1055-1MA00-0BA0 expansion module.

If the problem persists after attempting these solutions, please contact technical support.

8. Specifications

9. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your original purchase or contact Glintique customer service. Keep your purchase receipt as proof of purchase.

For further assistance, you may also consult the official Simatic LOGO! documentation and support resources.