JCKJWL Universal 24V PCB Control Board for Automatic Double-Arm Swing Gate Opener Instruction Manual

Introduction

Welcome and thank you for choosing the JCKJWL Universal 24V PCB Control Board. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your control board for automatic double-arm swing gate openers. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

Product Overview

Key Features

• Digital LED menu for straightforward setup and configuration.
• Supports operation for both single-leaf and double-leaf gates.
• Independent power adjustment for Motor 1 and Motor 2, including high-speed and low-speed settings for precise motor control.
• Adjustable auto-closing time, configurable from 1 second to 99 seconds.
• Integrated 60-second total working time limit to protect motors from overheating.
• Dedicated terminals for connecting external safety and control devices such as loop detectors, photocells, push buttons, keypads, and access control equipment.
• Compatible with both electric and electromagnetic locking mechanisms.
• Additional relay output for pedestrian gate lock control or other external devices.
• Utilizes a custom rolling code technology for enhanced system security.
• Provisions for connecting a backup battery or integrating with a solar power system.

Components

The JCKJWL Universal 24V PCB Control Board system typically includes the main control board and remote controls for wireless operation.

Image: JCKJWL Universal 24V PCB Control Board with two remote controls. This image displays the JCKJWL Universal 24V PCB Control Board, a green circuit board with various electronic components, terminals, and an LED display. Two remote controls are shown below the board.

Image: JCKJWL Universal 24V PCB Control Board with four remote controls. A view of the JCKJWL Universal 24V PCB Control Board, highlighting its components and terminals, accompanied by four remote controls.

Setup and Installation

Wiring Diagram Overview

Proper wiring is crucial for the safe and correct operation of your gate opener system. Always ensure power is disconnected before performing any wiring.

Power Connection

• The control panel accepts a voltage input of 12V/24V DC/AC.
• The motor output voltage is 24V DC.
• A 12V backup battery can be connected to the designated terminals for uninterrupted operation during power outages.

Motor Connections

Connect Motor 1 and Motor 2 to their respective terminals on the control board. Refer to your gate opener's motor manual for specific wiring requirements.

Accessory Connections

The board provides terminals for various accessories:

• Loop detector
• Photocell (safety beam)
• Push button
• Keypad
• Access control equipment
• An extra relay output is available for connecting electric or electromagnetic locks, or other external devices.

Image: JCKJWL 24V PCB Control Board with labeled connections. This image illustrates key connection points on the JCKJWL 24V PCB Control Board, including the 12V input for a backup battery, the 'FUN LED' indicator, and the connection for a three-wire output transformer.

Image: Close-up of a red connector on the JCKJWL 24V PCB Control Board. A detailed view of a red connector on the JCKJWL 24V PCB Control Board, indicating a specific connection point for wiring.

Image: JCKJWL 24V PCB Control Board installed within a protective housing. The JCKJWL 24V PCB Control Board is shown mounted inside a grey protective enclosure, with wiring connected to a large toroidal transformer, demonstrating a typical installation setup.

Remote Control Pairing

To pair a remote control with the PCB board, locate the 'LEARN' button on the board. Press and hold the 'LEARN' button until the LED indicator changes (refer to the board's specific LED behavior). While the LED is active, press a button on your remote control. The LED should indicate successful pairing. Repeat for additional remotes.

Image: JCKJWL 24V PCB Control Board next to a single remote control. The JCKJWL 24V PCB Control Board is displayed alongside one of its remote controls, illustrating the components that work together for gate operation.

Operating Instructions

Digital LED Menu Navigation

The control board features a digital LED display and control buttons (e.g., FUN, LEARN) for navigating settings. Use these buttons to cycle through menu options and adjust parameters as indicated on the LED display.

Adjusting Settings

• Single/Double Leaf Operation: Access the menu to select whether the system operates a single gate leaf or two gate leaves.
• Motor Power Settings: Adjust the power output for Motor 1 and Motor 2 independently. Fine-tune high-speed and low-speed settings to match your gate's requirements and ensure smooth operation.
• Auto-Closing Time: Set the delay before the gate automatically closes after opening. This can be configured from 1 second to 99 seconds.
• Total Working Time: The system is designed with a 60-second maximum continuous working time to prevent motor damage. This setting is fixed for motor protection.

Maintenance

Regular maintenance ensures the longevity and reliable operation of your control board and gate system.

• Periodically inspect all wiring and connections for signs of wear, corrosion, or looseness. Ensure all terminals are securely fastened.
• Keep the control board clean and free from dust, debris, and moisture. Ensure the enclosure is properly sealed if applicable.
• Regularly test the functionality of all connected safety devices, such as photocells and loop detectors, to ensure they are operating correctly.
• Check the backup battery (if installed) periodically to ensure it holds a charge and is ready for use during power outages.

Troubleshooting

If you encounter issues with your JCKJWL Universal 24V PCB Control Board, refer to the following common troubleshooting steps:

• No Power: Check the main power supply to the control board. Verify all power connections and fuses.
• Gate Does Not Open/Close: Ensure all motor connections are secure. Check for any physical obstructions preventing gate movement. Verify that safety devices (photocells, loop detectors) are not triggered.
• Remote Control Unresponsive: Check the battery in the remote control. If the battery is functional, attempt to re-pair the remote control with the control board as described in the 'Remote Control Pairing' section.
• Erratic Operation: Inspect all wiring for loose connections or damage. Ensure no interference from other electronic devices. Refer to the digital LED display for any error codes that may provide specific diagnostic information.
• Gate Stops Mid-Cycle: This could indicate an obstruction, a safety device trigger, or the 60-second motor protection limit being reached. Clear any obstructions and check safety devices.

If problems persist after following these steps, please contact technical support.

Specifications

Warranty and Support

Specific warranty information for the JCKJWL Universal 24V PCB Control Board is not provided in this manual. For details regarding warranty coverage, technical support, or service inquiries, please contact the manufacturer, JCKJWL, or your original point of purchase. Ensure you have your product model number (1245644516312323153) and purchase date available when seeking support.