Introduction
This manual provides essential information for the safe and correct installation, operation, maintenance, and troubleshooting of the Generic replacement oven bake element, part number 352512. This element is designed as a compatible replacement for specific Frigidaire oven models. Please read all instructions carefully before proceeding with installation or any maintenance.
Safety Information
WARNING: To reduce the risk of electric shock, fire, or injury to persons, observe the following:
- Always disconnect power to the oven at the circuit breaker or fuse box before attempting any installation, repair, or maintenance. Failure to do so can result in serious injury or death.
- Installation should only be performed by a qualified technician. Improper installation can lead to appliance malfunction, property damage, or personal injury.
- Wear appropriate personal protective equipment, such as gloves and eye protection, during installation.
- Ensure the replacement part is compatible with your specific oven model before beginning installation. Refer to the compatibility section of this manual.
- After installation, ensure all connections are secure and the element is properly seated before restoring power.
Compatibility
This replacement bake element (part number 352512) is compatible with the following Frigidaire oven models:
- LFEF3018TWD
- FFEF3005MWB
- FEF352FWB
- FEFL67DCH
Always verify your oven's model number against this list and compare the physical appearance of the new element with your original part before installation.
Installation Instructions
Disclaimer: Installation of this part requires electrical knowledge and should ideally be performed by a qualified appliance repair technician. Proceed with caution and at your own risk.
- Disconnect Power: Locate your oven's circuit breaker in your home's electrical panel and turn it OFF. Confirm power is off by attempting to turn on the oven.
- Access Oven Interior: Open the oven door completely.
- Remove Old Element:
- Locate the existing bake element at the bottom of the oven cavity.
- Using a screwdriver, remove the screws securing the element to the back wall of the oven.
- Carefully pull the element forward a few inches. This will expose the electrical terminals.
- Disconnect Wires: Note the position of the wires connected to the old element's terminals. Disconnect these wires. It is recommended to take a photo for reference. Ensure the wires do not retract into the oven wall.
- Remove Old Element: Once wires are disconnected, fully remove the old element from the oven.
- Connect New Element: Connect the electrical wires to the terminals of the new bake element. Ensure connections are firm and secure.
- Install New Element: Carefully slide the new element into position, ensuring the terminals align with the holes in the back wall. Push the element fully into place.
- Secure Element: Reinstall the screws to secure the new element to the back wall of the oven.
- Restore Power: Close the oven door. Return to your electrical panel and turn the oven's circuit breaker ON.
- Test Operation: Turn on the oven to a bake setting and observe if the new element heats up properly.
Image 1: Top view of the Generic Oven Bake Element (Part #352512). This shows the general shape and terminal connections.
Image 2: Angled view of the Generic Oven Bake Element (Part #352512). This perspective highlights the mounting brackets and terminal ends.
Operation
The bake element functions as an integral part of your oven's heating system. Once properly installed, it will operate automatically when the oven is set to a bake or preheat cycle, converting electrical energy into heat to cook food. No direct user interaction with the element itself is required for operation.
Maintenance
Regular maintenance helps ensure the longevity and efficient operation of your oven and its components.
- Cleaning: If food spills occur on the bake element, allow the oven to cool completely and disconnect power before attempting to clean. Gently wipe the element with a damp cloth. Avoid using abrasive cleaners or harsh chemicals, as these can damage the element's surface.
- Inspection: Periodically inspect the element for any visible signs of damage, such as cracks, blisters, or discoloration. If any damage is observed, disconnect power and consider replacing the element to prevent further issues.
- Professional Check: For comprehensive maintenance, consider having your oven inspected by a qualified technician annually.
Troubleshooting
If your oven is not heating correctly after replacing the bake element, consider the following common issues:
| Problem | Possible Cause | Solution |
|---|---|---|
| Oven not heating at all. |
|
|
| Oven heating unevenly. |
|
|
| Element sparking or arcing. |
|
|
For issues not listed here or if troubleshooting steps do not resolve the problem, it is recommended to contact a qualified appliance repair technician.
Specifications
| Manufacturer | Generic |
| Part Number | bakepart#352512 |
| Item Package Quantity | 1 |
| ASIN | B0F635GHK5 |
| First Available | April 23, 2025 |
Warranty Information
Specific warranty details for this Generic replacement part are not provided in the product information. Please refer to the retailer's return policy or contact the manufacturer directly for any warranty-related inquiries.
Customer Support
For further assistance, technical support, or questions regarding this replacement part, please contact the retailer from whom the product was purchased. For general appliance repair advice, it is recommended to consult a certified appliance technician.