11026002011

Replacement Washer Drive Belt Instruction Manual

Instruction Manual

1. Product Overview

This manual provides essential information for the installation, maintenance, and troubleshooting of your new replacement washer drive belt. This component is crucial for the proper operation of your washing machine, transmitting power from the motor to the wash drum.

Black rubber washer drive belt on a white grid background

Figure 1: The replacement washer drive belt. This belt is designed to connect the motor to the washing machine's drum, enabling the agitation and spin cycles.

2. Compatibility

This replacement drive belt is compatible with a wide range of washing machine models from various brands. Please verify your appliance's model number against the list below to ensure proper fit and function.

Compatible Brands and Models:

Note: This list is not exhaustive. If your model is not listed, please cross-reference the part number with your appliance's specifications or consult a qualified technician.

3. Installation Instructions

Safety First: Always disconnect the washing machine from its power source and water supply before beginning any repair. Wear appropriate safety gear, such as gloves.

  1. Access the Drive System: Depending on your washer model, you may need to remove the back panel, front panel, or tilt the machine to access the motor and drum pulley assembly. Refer to your specific washer's service manual for detailed access instructions.
  2. Locate the Old Belt: Identify the existing drive belt connecting the motor pulley to the large drum pulley.
  3. Remove the Old Belt: Carefully remove the old belt. This may involve releasing tension from an idler pulley or simply rolling the belt off the pulleys.
  4. Install the New Belt:
    • Place the new belt around the smaller motor pulley first.
    • Then, stretch the belt around the larger drum pulley. It may be necessary to hold the belt on the motor pulley with one hand while rotating the drum pulley by hand to guide the belt into place.
    • Ensure the belt is seated correctly in the grooves of both pulleys.
  5. Verify Tension: The belt should be taut but not overly tight. If your model has an idler pulley, ensure it applies proper tension.
  6. Reassemble: Reattach any panels or components removed during access.
  7. Test Operation: Reconnect power and water. Run a short cycle to ensure the washer operates correctly and the drum spins and agitates as expected. Listen for any unusual noises.

4. Maintenance

The drive belt is a wear item and does not typically require routine maintenance beyond proper installation. However, periodic inspection can extend its lifespan and prevent future issues:

5. Troubleshooting Common Issues

SymptomPossible CauseSolution
Washer not spinning or agitatingBroken or slipped drive beltInspect and replace belt if broken. Re-seat belt if slipped.
Loud squealing noise during operationWorn, glazed, or misaligned drive beltInspect belt for wear. Clean belt and pulleys. Ensure proper alignment. Replace if severely worn.
Burning rubber smellBelt slipping due to overload or worn pulleysReduce load size. Inspect pulleys for damage. Replace belt if damaged.

If troubleshooting steps do not resolve the issue, it is recommended to consult a qualified appliance repair technician.

6. Product Specifications

AttributeDetail
Part Number‎11026002011
Item Model Number‎11026002011
Included Components‎Washer Drive Belt
Product Dimensions‎1 x 1 x 1 inches
Manufacturer‎Generic
ASINB0F5SPJ771
Date First AvailableApril 21, 2025

7. Support and Warranty

For further assistance or warranty information, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

This product is designed as a direct replacement part. Performance and longevity may vary based on appliance usage and environmental factors.

Documents - 11026002011 – 11026002011
[pdf] Document
cbe4bc3325e1268354735127be3868529269971b2702ec3287c34e08c36a1255 xlsx Work2 Cross Reference and Model Information Lid Latch Assembly Part 7MWTW1905DW0 WASHER Whirlpool AUTOMATIC Maytag MVWX600BW0 MVWX600XL0 MVWX600XL1 AUTOMATIC  51GHTAsPERS m media amazon images I |||
Cross Reference and Model Information Lid Latch Assembly Part Number: AP5263307 Manufacturer s Part ... MATIC WASHER 11021392011 AUTOMATIC WASHER 11021392012 AUTOMATIC WASHER 11026002010 AUTOMATIC WASHER 11026002011 AUTOMATIC WASHER 11026012010 AUTOMATIC WASHER 11026012011 AUTOMATIC WASHER 11028002010 A...
score:23 filesize: 52.05 K page_count: 5 document date: 2019-04-02
[pdf] Document
51WR1eTHMqL images na ssl amazon I |||
Manufacturer Kenmore / Sears Kenmore / Sears Kenmore / Sears Kenmore / Sears Kenmore / Sears Kenmore ... C WASHER 11021392011 AUTOMATIC WASHER 11021392012 AUTOMATIC WASHER 11026002010 AUTOMATIC WASHER 11026002011 AUTOMATIC WASHER 11026012010 AUTOMATIC WASHER 11026012011 AUTOMATIC WASHER 1102800201...
score:22 filesize: 58.76 K page_count: 6 document date: 2017-08-01