Kobi FALA II Children's Bed with Trundle and Mattresses, 160x80

1. Introduction

This manual provides essential information for the safe assembly, operation, and maintenance of your Kobi FALA II Children's Bed. Please read these instructions carefully before assembly and retain them for future reference. The FALA II bed is designed for children, featuring a main bed and a pull-out trundle bed, complete with two mattresses.

Image 1.1: The Kobi FALA II Children's Bed with its trundle bed extended, shown in a typical child's bedroom environment.

2. Safety Information

WARNING: Failure to follow these safety instructions could result in serious injury.

• Always supervise children when they are using the bed, especially the trundle feature.
• Ensure all assembly hardware is securely tightened before use. Periodically check and re-tighten as necessary.
• Keep small parts out of reach of children during assembly to prevent choking hazards.
• Do not allow children to jump on the bed.
• The bed features rounded edges and removable railings for safety. Ensure railings are properly installed when needed.
• The maximum load capacity for each bed (main and trundle) is 110 kg. Do not exceed this weight limit.
• Only use mattresses of the specified dimensions (160x80 cm for the main bed, 145x70 cm for the trundle bed) to ensure proper fit and safety.

3. Package Contents

Before beginning assembly, verify that all components listed below are present:

• Bed frame components (headboard, footboard, side rails)
• Trundle bed frame components
• 2 x FLEX slatted frames (one for main bed, one for trundle)
• 1 x Mattress (160x80 cm)
• 1 x Mattress (145x70 cm)
• Assembly hardware kit (screws, dowels, etc.)
• Assembly instructions (this document)

4. Assembly Instructions

Assembly requires two adults. Please follow the steps carefully. Tools required: Phillips head screwdriver (not included).

1. Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
2. Assemble Main Bed Frame: Attach the side rails to the headboard and footboard using the provided hardware. Ensure all connections are secure. The design allows for the bed to be mounted with the opening on the right or left side, adapting to your room layout.
3. Install Main Bed Slatted Frame: Place the 160x80 cm FLEX slatted frame into the main bed frame. Ensure it sits securely on the support ledges.
4. Assemble Trundle Bed Frame: Assemble the trundle bed frame following the specific instructions in your hardware kit. This typically involves attaching the side panels to the front and back panels, and then attaching the wheels.
5. Install Trundle Bed Slatted Frame: Place the 145x70 cm FLEX slatted frame into the trundle bed frame.
6. Place Mattresses: Position the 160x80 cm mattress on the main bed's slatted frame and the 145x70 cm mattress on the trundle bed's slatted frame.
7. Final Check: Verify that all screws and fasteners are tight and that the bed is stable.

Image 4.1: Detail view of the bed's construction, highlighting the mattress placement and the slatted frame system.

5. Operating Instructions

5.1 Using the Trundle Bed

The FALA II bed features a convenient pull-out trundle bed for additional sleeping space.

• To extend the trundle bed, gently pull the front panel of the lower bed outwards from under the main bed. The wheels will allow it to slide smoothly.
• To retract the trundle bed, push it back under the main bed until it is fully nested.

5.2 Removable Railings

The bed is equipped with removable railings to prevent falls. Ensure these are securely attached when a child is sleeping in the bed. To remove or attach, follow the specific mechanism detailed in your assembly kit.

6. Maintenance

6.1 Cleaning the Bed Frame

• Wipe the bed frame with a soft, damp cloth.
• Avoid using abrasive cleaners, harsh chemicals, or solvents, as these can damage the finish.
• Dry immediately with a clean cloth.

6.2 Mattress Care

The mattresses provided are designed for comfort and durability. Refer to the care labels on the mattresses for specific cleaning instructions. Generally:

• Rotate and flip mattresses regularly to ensure even wear.
• Use a mattress protector to guard against spills and stains.
• Spot clean stains with a mild detergent and water, then allow to air dry completely.

Image 6.1: Mattress care symbols and a child sleeping, emphasizing the comfort and safety features of the mattress.

Image 6.2: Illustration of the mattress's layered construction, highlighting its design for support and comfort.

7. Troubleshooting

• Bed feels wobbly: Check all assembly hardware and re-tighten any loose screws. Ensure the bed is on a flat, even surface.
• Trundle bed not sliding smoothly: Check for any obstructions under the bed. Ensure the wheels are clean and free of debris.
• Parts missing or damaged: Refer to the contact information in the Warranty & Support section for assistance.

8. Specifications

Image 8.1: Detailed dimensions of the Kobi FALA II Children's Bed.

Image 8.2: Detailed dimensions of the trundle bed drawer.

9. Warranty & Support

For warranty information, spare parts availability, or technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty claims.

For further assistance, please visit the KOBI brand store: KOBI Brand Store