ORALOCK 101697_1033

ORALOCK Pull Starter Instruction Manual

For Briggs & Stratton Models 126T02-1135-B1, 126T02-1137-B1, 126T02-1155-B1

1. Product Overview

This manual provides instructions for the installation, operation, and maintenance of your ORALOCK Pull Starter. This component is designed to replace the original pull starter on compatible Briggs & Stratton engines, facilitating manual engine ignition.

ORALOCK Pull Starter

Image 1.1: The ORALOCK Pull Starter. This component is a black, circular unit with a grated top and an attached black handle for manual engine starting.

2. Compatibility

The ORALOCK Pull Starter (Model 101697_1033) is compatible with the following Briggs & Stratton engine models:

  • 126T02-1135-B1
  • 126T02-1137-B1
  • 126T02-1155-B1

Please verify your engine's model number to ensure proper fitment before installation. Refer to your engine's documentation for its specific model identification.

3. Safety Information

Always prioritize safety when working with engine components. Failure to follow safety precautions can result in injury or damage to equipment.

  • Disconnect Spark Plug: Before performing any work on the engine, always disconnect the spark plug wire to prevent accidental starting.
  • Wear Protective Gear: Use appropriate personal protective equipment, including safety glasses and gloves.
  • Engine Cool Down: Allow the engine to cool completely before handling any parts to avoid burns.
  • Secure Work Area: Ensure your work area is clean, well-lit, and free of obstructions.
  • Proper Tools: Use the correct tools for each task to prevent damage to fasteners and components.

4. Setup and Installation

This section outlines the general steps for replacing a pull starter. Specific procedures may vary slightly depending on your engine model. Consult your engine's service manual for detailed instructions if necessary.

  1. Preparation: Ensure the engine is off and cool. Disconnect the spark plug wire.
  2. Locate Old Starter: Identify the existing pull starter assembly on your engine. It is typically mounted on the engine housing with several bolts.
  3. Remove Old Starter: Using appropriate tools (e.g., a socket wrench), carefully unbolt and remove the old pull starter assembly. Note the position and orientation of any gaskets or spacers.
  4. Inspect Mounting Area: Clean the mounting surface on the engine to ensure a proper seal for the new starter.
  5. Install New Starter: Position the ORALOCK Pull Starter onto the engine, aligning the mounting holes. Ensure the starter rope is correctly oriented.
  6. Secure New Starter: Insert and tighten the mounting bolts. Do not overtighten, as this can strip threads or crack the housing.
  7. Reconnect Spark Plug: Once the new starter is securely installed, reconnect the spark plug wire.
  8. Test: Gently pull the starter rope a few times to ensure it engages and retracts smoothly.

It is crucial to double-check the part's appearance and dimensions against your original part to ensure a perfect fit before installation.

5. Operation

To start your engine using the ORALOCK Pull Starter:

  1. Ensure the engine's fuel supply is on and the choke (if applicable) is set correctly for a cold start.
  2. Grasp the starter handle firmly.
  3. Pull the rope slowly until you feel resistance (the compression stroke).
  4. Give a quick, strong pull on the rope, extending your arm fully. Do not let the rope snap back; guide it gently as it retracts.
  5. Repeat pulling until the engine starts.
  6. Once the engine starts, allow the rope to fully retract into the starter housing.

6. Maintenance

Regular maintenance helps ensure the longevity and reliable operation of your pull starter.

  • Keep Clean: Periodically clean the exterior of the starter assembly to prevent dirt and debris from entering the mechanism.
  • Inspect Rope: Regularly check the starter rope for fraying, cuts, or excessive wear. Replace the rope if any damage is observed.
  • Check Recoil Spring: Ensure the rope retracts fully and smoothly after each pull. If it's sluggish, the recoil spring may need inspection or replacement (this is an advanced repair, often requiring professional service).
  • Mounting Bolts: Periodically check that the mounting bolts are secure.

7. Troubleshooting

If you encounter issues with your pull starter, consider the following common problems and solutions:

  • Rope Does Not Retract: This often indicates a problem with the recoil spring or internal mechanism. Ensure the rope is not tangled. If the spring is broken, the starter assembly may need replacement or professional repair.
  • Rope Pulls Out Completely: The rope may have detached from the internal mechanism or the spring is broken. The starter assembly will likely need replacement.
  • Engine Does Not Start After Pulling: This is typically an engine-related issue, not the pull starter itself. Check fuel, spark plug, and carburetor. Ensure the spark plug wire is connected.
  • Hard to Pull: Ensure the engine is not seized. Check for proper lubrication and ensure the choke is not causing excessive resistance.

8. Specifications

  • Brand: ORALOCK
  • Model Number: 101697_1033
  • Compatibility: Briggs & Stratton 126T02-1135-B1, 126T02-1137-B1, 126T02-1155-B1
  • Material: Durable construction for longevity
  • Purpose: Replacement pull starter for efficient engine ignition

9. Warranty and Support

For information regarding warranty coverage or technical support for your ORALOCK Pull Starter, please refer to the retailer's return policy or contact ORALOCK customer service directly through their official channels. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.