Larimuer Fingerprint Fridge Lock

Product Overview

The Larimuer Fingerprint Fridge Lock (Model FQ20) is an advanced biometric security device designed to provide keyless and password-free access control. It is ideal for child and pet proofing various household items such as refrigerators, drawers, cabinets, ovens, and toilets. This lock features a highly sensitive fingerprint sensor, a durable steel wire cable, and multiple installation options for versatile use.

Image: The Larimuer Fingerprint Fridge Lock securely installed on a refrigerator, showcasing its compact design and cable connection between the two lock components.

Package Contents

Please verify that all items listed below are included in your package:

• 1 x Smart Fingerprint Lock (Black)
• 1 x Instruction Manual
• 1 x Type-C Charging Cable
• 1 x Emergency Unlock USB Key
• 1 Set of Screws

Image: A visual representation of the package contents, showing the fingerprint lock, instruction manual, Type-C charging cable, emergency USB key, and a set of screws.

Setup and Installation

The Larimuer Fingerprint Fridge Lock offers two installation methods: adhesive or screw-based. Choose the method best suited for your application.

Installation Steps (Adhesive Method)

1. Clean the Surface: Locate the desired installation area and thoroughly clean the surface to ensure it is dry and free of dust or grease.
2. Apply Primer (Optional, for enhanced adhesion): If desired, use an adhesion promoter wipe (not included) on the cleaned surface for stronger bonding. Allow to dry completely.
3. Prepare the Lock: Tear off the protective film from the self-adhesive pads on both parts of the lock.
4. Attach the Lock: Carefully align and firmly press each part of the lock onto the prepared surface for a few seconds.
5. Curing Time: Allow 48 hours after installation for the adhesive to fully bond and ensure maximum load-bearing capacity (up to 40kg).

Installation Steps (Screw Method)

1. Position the Lock: Place the lock components in the desired positions on the surface.
2. Mark Drill Points: Use a pencil to mark the screw holes on the surface through the designated points on the lock components.
3. Drill Pilot Holes: Carefully drill pilot holes at the marked points.
4. Secure with Screws: Use the provided screws and an electric screwdriver to securely fasten both parts of the lock to the surface.

Image: A step-by-step guide illustrating the adhesive installation process, from cleaning the surface to allowing the adhesive to cure.

Installation Video

Video: This video demonstrates the installation process of the fingerprint lock, showing how to attach it to a surface.

Operating Instructions

The fingerprint lock supports up to 20 registered fingerprints for convenient access.

Initial Fingerprint Enrollment (First Two Fingerprints)

For the first-time setup, you must register two fingerprints to activate the lock.

1. Activate Enrollment: Long press the fingerprint sensor until the blue light turns on, then lift your finger.
2. Register First Finger: Place your first finger on the sensor and lift it 10 times continuously, moving your finger slightly to capture different angles. The green light will flash 10 times and then stop, indicating successful registration of the first fingerprint.
3. Register Second Finger: Repeat the process with a different finger (your second finger). Place it on the sensor and lift it 10 times continuously, moving it to capture various angles. The green light will flash 10 times and then stop, indicating successful registration of the second fingerprint.
4. The lock is now ready for use with the registered fingerprints.

Adding Additional Fingerprints

After the initial two fingerprints are set, you can add up to 18 more fingerprints (total of 20).

1. Verify with Registered Finger: Place any already registered finger on the sensor until the green light flashes once, indicating successful verification.
2. Activate Enrollment: Immediately after verification, long press the fingerprint sensor until the blue light turns on, then lift your finger.
3. Register New Finger: Place the new finger on the sensor and lift it 10 times continuously, moving your finger slightly to capture different angles. The green light will flash 10 times and then stop, indicating successful registration.
4. Repeat for any additional fingerprints you wish to add.

Image: A visual guide detailing the process of enrolling fingerprints, including the initial long press and subsequent multiple presses for each finger.

Fingerprint Enrollment Videos

Video: A tutorial demonstrating the fingerprint enrollment process for the fridge lock.

Video: This video explains the initial setup, emphasizing the need to set two fingerprints for the first-time use of the fingerprint lock.

Video: A demonstration on how to add a new fingerprint to the device.

Video: Instructions on how to add a new fingerprint to the lock.

Video: An alternative method for entering a new fingerprint into the lock.

Unlocking the Lock

Simply place a registered finger on the fingerprint sensor. The lock will unlock instantly if the fingerprint is recognized.

Image: This image illustrates the one-touch fingerprint unlocking process and the different light indicators for verification status and fingerprint enrollment.

Emergency Unlock with USB Key

In case of low battery or inability to unlock with a registered fingerprint, use the emergency USB key.

1. Insert USB Key: Insert the emergency USB key into the USB port on the lock.
2. Supply Power: Connect a 5V adapter or power bank (not included) to the USB key to supply power.
3. Unlock: The lock will automatically unlock. Note that using the emergency USB key will restore factory settings and delete all registered fingerprints.

Video: This video demonstrates how to use the USB emergency key to unlock the device.

Video: Instructions on when and how to use the emergency unlock USB key for the fingerprint lock.

Maintenance

Charging the Lock

The lock features a built-in rechargeable battery. A Type-C USB cable is included for charging.

• Connect the Type-C cable to the charging port on the lock.
• Connect the other end of the cable to a 5V adapter or power bank (not included).
• A full charge takes approximately 1.5 to 2 hours.
• A fully charged lock can last about 10 months if opened 5 times a day.
• The lock will provide a low-energy alert (red light) when the battery is low.

Image: This image demonstrates how to charge the fingerprint lock using the Type-C USB cable, connecting it to either a power bank or a wall adapter.

Troubleshooting

• Fingerprint Not Recognized: Ensure your finger is clean and dry. Try repositioning your finger on the sensor. If multiple attempts fail, use a different registered finger or the emergency USB key.
• Low Battery: The lock will indicate a low battery with a red light. Recharge the device using the provided Type-C cable. If the battery is completely depleted, use the emergency USB key to unlock and then recharge.
• Cannot Add Fingerprints: Ensure you are following the correct enrollment procedure, including the initial two-fingerprint setup. If the blue light does not appear, the lock might be in an unlocked state or require a reset via the emergency USB key.
• Accidental Deletion of Fingerprints: If all fingerprints are accidentally deleted (e.g., after using the emergency USB key), you will need to re-enroll the first two fingerprints as per the initial setup instructions.

Specifications

Warranty and Support

For warranty information, technical support, or any product-related inquiries, please contact Larimuer customer service directly through your purchase platform or the contact details provided with your product packaging.