Introduction
This manual provides instructions for the VINABTY Replacement Remote Control, model MB2716. This remote is designed as a direct replacement for various Q.Bell TV models, offering seamless operation without the need for complex programming.
It is compatible with a wide range of Q.Bell models, including QT32A02, AGL390087, QT32B03, AGL390057, QT32X13, AGL390047, QT32X03, AGL390009, QT32A03, QT55X23, QT43X23, QT50X23, QT58X23, QT24B03, AGL39112, QT40A03, and AGL390048.
Setup
1. Battery Installation
The VINABTY remote control requires two (2) AAA alkaline batteries for operation. Batteries are not included with the remote control.
- Locate the battery compartment on the back of the remote control.
- Slide the battery compartment cover downwards to open it.
- Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery compartment cover back into place until it clicks securely.
Figure 1: Battery compartment with AAA batteries inserted.
2. Initial Use
This VINABTY replacement remote control is pre-programmed and requires no additional setup or configuration. Once batteries are installed, it is ready for immediate use with compatible Q.Bell TV models.
Operating Instructions
Point the remote control directly at the infrared receiver on your Q.Bell TV. The maximum effective range is approximately 10 meters (33 feet).
Figure 2: Layout of the VINABTY remote control buttons.
Button Functions Overview
| Button | Function |
|---|---|
| STAND BY (Red Power Button) | Turns the TV on or off (standby mode). |
| SOURCE | Selects the input source (e.g., HDMI, AV, TV). |
| 0-9 (Number Buttons) | Direct channel selection. |
| FAV | Accesses favorite channels list. |
| P.MODE | Cycles through picture modes (e.g., Standard, Dynamic, Movie). |
| S.MODE | Cycles through sound modes (e.g., Standard, Music, Movie). |
| SLEEP | Sets the sleep timer. |
| DISPLAY | Displays current channel information or on-screen display. |
| TV/RADIO | Switches between TV and Radio modes. |
| Navigation Buttons (Up, Down, Left, Right) | Navigates menus and options. |
| OK | Confirms selections in menus. |
| MENU | Opens the main menu. |
| EXIT | Exits the current menu or function. |
| MUTE | Mutes or unmutes the TV sound. |
| VOL +/- | Adjusts the volume level. |
| CH +/- | Changes the channel up or down. |
| CH LIST | Displays the channel list. |
| FREEZE | Freezes the current image on screen. |
| MEDIA | Accesses media playback functions. |
| AUDIO I/II | Selects audio language or mode. |
| ASPECT / SIZE | Adjusts the screen aspect ratio or picture size. |
| SUBPAGE | Accesses teletext subpages. |
| SUBTITLE | Toggles subtitles on or off. |
| TEXT | Opens teletext. |
| REVERAL | (Function may vary, often related to teletext or media playback). |
| HOLD | Holds the current teletext page. |
| INDEX | Accesses teletext index page. |
| MIX | Mixes teletext with TV picture. |
| Media Playback Controls (Rewind, Play/Pause, Fast Forward, Previous, Stop, Next) | Controls media playback (e.g., USB, connected devices). |
| Colored Buttons (Red, Green, Yellow, Blue) | Functions vary depending on the TV model and current menu/application. Often used for specific teletext or smart TV features. |
Maintenance
Cleaning the Remote Control
To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, waxes, or solvents. These can damage the surface and internal components.
Battery Replacement
Replace batteries when the remote control's response becomes sluggish or stops working. Always replace both batteries at the same time with new AAA alkaline batteries. Do not mix old and new batteries, or different types of batteries.
Storage
If the remote control will not be used for an extended period, remove the batteries to prevent leakage and potential damage to the remote.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote control is not working. | Batteries are dead or inserted incorrectly. | Check battery polarity. Replace batteries with new AAA alkaline batteries. |
| Remote control range is poor. | Low batteries; Obstruction between remote and TV; Remote not pointed at TV's IR sensor. | Replace batteries. Ensure clear line of sight to the TV. Point the remote directly at the TV's infrared sensor. |
| Some buttons are not responding. | Specific button malfunction; TV model incompatibility for certain advanced functions. | Ensure the remote is compatible with your specific Q.Bell TV model. If only a few buttons are unresponsive, the remote may be faulty. |
Specifications
| Feature | Detail |
|---|---|
| Brand | VINABTY |
| Model | MB2716 |
| Compatible Devices | Q.Bell QT32A02, AGL390087, QT32B03, AGL390057, QT32X13, AGL390047, QT32X03, AGL390009, QT32A03, QT55X23, QT43X23, QT50X23, QT58X23, QT24B03, AGL39112, QT40A03, AGL390048 |
| Connectivity Technology | Infrared |
| Controller Type | Button Control |
| Special Features | Ergonomic, Pre-Programmed |
| Maximum Range | 10 Meters |
| Batteries Required | Yes (2 x AAA) |
| Battery Type | Alkaline |
| Product Dimensions | 12 x 4 x 1 cm |
| Item Weight | 40 g |
Customer Support
For any issues or inquiries regarding your VINABTY Replacement Remote Control, please do not hesitate to contact our customer service. We are committed to providing comprehensive support for our products.
If you are unsure about the compatibility of this remote control with your device, you may send pictures of your original remote control to our support team for verification before purchase.
