Caruner Aluminum Steering Group Upgrade Kit

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the Caruner Aluminum Steering Group Upgrade Kit (Model CN YF-0576). This kit is designed as a direct replacement and upgrade for the stock steering components of the LOSI 1/24 Micro-B 2WD Buggy RTR-LOS00007 RC Car. Upgrading to aluminum components can enhance durability and steering precision.

Figure 1.1: Overview of the Caruner Aluminum Steering Group Upgrade Kit components. This image displays the main aluminum steering arm, two bearing cups, and four small bearings, all in black finish.

2. Package Contents

Verify that all components listed below are present in your package before beginning installation. If any parts are missing or damaged, please contact customer support.

• 1x Aluminum Steering Arm (Black)
• 2x Aluminum Bearing Cups (Black)
• 4x Ball Bearings
• (Screws and other small hardware may be pre-installed or included separately)

Figure 2.1: Detailed view of the kit's components, including the steering arm, two bearing cups, and four ball bearings. The steering arm features threaded holes for attachment.

3. Safety Information

Please read and understand all safety precautions before proceeding with installation.

• Adult Supervision: This product contains small parts and is intended for users 14 years and older. Adult supervision is recommended during installation.
• Tools: Use appropriate tools for disassembly and assembly to prevent damage to components or injury.
• Small Parts: Keep small parts away from children and pets to prevent choking hazards.
• Static Electricity: Handle electronic components with care to avoid damage from static discharge.
• Disassembly: Refer to your RC car's original manual for specific disassembly instructions if needed.

4. Installation Guide

Follow these steps carefully to install the aluminum steering group upgrade kit onto your LOSI 1/24 Micro-B 2WD Buggy.

4.1. Preparation

1. Power off your RC car and disconnect the battery.
2. Place the RC car on a clean, flat surface.
3. Gather necessary tools, such as a small Phillips head screwdriver and hex wrenches (not included).

4.2. Removing the Stock Steering Group

1. Carefully locate the existing steering group assembly on your LOSI 1/24 Micro-B. This typically involves the steering servo horn, linkage, and the plastic steering rack.
2. Using appropriate tools, unscrew and detach the steering linkage from the servo horn and the stock steering rack.
3. Remove any screws securing the stock plastic steering rack to the chassis. Keep these screws organized as some may be reused.
4. Gently remove the entire stock steering group assembly.

4.3. Assembling the Aluminum Steering Group

1. Take the aluminum steering arm. Note the threaded holes for mounting.

Figure 4.1: Close-up view of the black aluminum steering arm, highlighting its design and threaded attachment points.
2. Insert the four ball bearings into the designated slots within the two aluminum bearing cups. Ensure they fit snugly.


Figure 4.2: Close-up view of one of the black aluminum bearing cups, showing the recess for a ball bearing and the pivot point.

3. Attach the bearing cups to the aluminum steering arm using the provided screws (if separate) or by utilizing the pre-installed threaded posts on the steering arm. Ensure the bearings are properly seated and allow for smooth movement. Do not overtighten.

4.4. Installing the New Steering Group

1. Position the assembled aluminum steering group onto the chassis where the original steering rack was located.
2. Secure the aluminum steering group to the chassis using the screws removed in step 4.2.3, or new screws if provided. Ensure it is firmly attached but still allows for free movement of the steering arm.
3. Reconnect the steering linkage from the servo horn to the appropriate attachment point on the new aluminum steering arm.
4. Verify that the steering moves freely from left to right without binding.

4.5. Post-Installation Check

1. Reconnect the battery and power on your RC car.
2. Test the steering function by turning the wheels left and right using your transmitter.
3. Adjust steering trim on your transmitter if the wheels are not centered.
4. Perform a slow test drive to ensure proper operation before full-speed use.

5. Maintenance

Regular maintenance will ensure the longevity and optimal performance of your aluminum steering group.

• Cleaning: Periodically clean the steering group to remove dirt, dust, and debris. Use a soft brush or compressed air. Avoid harsh chemicals.
• Inspection: Regularly inspect all screws and connections for tightness. Aluminum parts are durable, but impacts can cause loosening.
• Bearing Check: Check the ball bearings for smooth operation. If they feel gritty or bind, they may need cleaning or replacement.
• Lubrication: Lightly lubricate pivot points with a small amount of RC-safe grease or oil if movement becomes stiff. Avoid over-lubrication.

6. Troubleshooting

7. Specifications

8. Warranty and Customer Support

Caruner products are manufactured to high-quality standards. For any questions regarding installation, troubleshooting, or product defects, please contact Caruner customer support through the retailer's platform where the product was purchased. Please retain your proof of purchase for warranty claims.

For further assistance, visit the official Caruner store on Amazon: Caruner Store