Keeson MC120PR JLDP.15.020.011 Replacement Remote Control User Manual

1. Important Compatibility Information

This replacement remote control is specifically designed for adjustable beds equipped with the Keeson MC120PR JLDP.15.020.011 control box. It is crucial to verify your existing control box model number before attempting to use this remote.

Do not purchase or attempt to pair this remote if your control box model number does not match MC120PR JLDP.15.020.011.

Your current remote must have the same button layout and functions as this replacement remote for proper operation.

Figure 1: Example of a control box label (bottom right) and the back of a remote with battery compartment (top left). Ensure your control box label matches the specified model number.

If you are uncertain about compatibility, please consult your adjustable bed's original manual or contact the seller with detailed information about your bed, control box, and old remote control.

2. Setup and Pairing Instructions

2.1 Battery Installation

The remote control requires two (2) AAA batteries (not included). To install:

1. Locate the battery compartment cover on the back of the remote control.
2. Slide the cover downwards or press the latch to open it.
3. Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
4. Replace the battery compartment cover until it clicks securely into place.

Figure 2: Back of the remote control with the battery compartment.

2.2 Pairing Method

After installing batteries, the remote control must be paired with your adjustable bed's control box. Follow these steps carefully:

1. Step 1: On the remote control, simultaneously press and hold the "Head Up" button (upper-left arrow) and the "Foot Down" button (lower-right arrow) for approximately 10 seconds.
2. Step 2: Locate the control box underneath your bed. Find the pairing button, which is typically labeled "Learn" or "Reset Coding". Press and immediately release this button. Do not press and hold it.
3. Step 3: Listen for a series of beeps. These beeps indicate that the remote control has successfully synced with the control box.

If the remote does not pair, repeat the steps. Ensure the batteries are correctly installed and fully charged, and that you are within close proximity to the control box during the pairing process.

3. Operating the Remote Control

The remote control features several buttons for adjusting your adjustable bed. Refer to the image below for button identification.

Figure 3: Front view of the Keeson MC120PR JLDP.15.020.011 remote control.

• Head Up/Down Arrows: Adjusts the head section of the bed upwards or downwards.
• Foot Up/Down Arrows: Adjusts the foot section of the bed upwards or downwards.
• FLAT Button: Returns the bed to a completely flat position.
• ZG Button: Activates the Zero Gravity preset position, which elevates the head and foot to a position designed to relieve pressure.
• M1 / M2 Buttons: These are memory preset buttons. Press and hold to save a desired position, or press briefly to recall a saved position. Consult your bed's manual for specific instructions on setting memory positions.
• Flashlight Button (Torch Icon): Activates a built-in flashlight for convenience in low-light conditions.

4. Maintenance

To ensure the longevity and proper functioning of your remote control, follow these maintenance guidelines:

• Battery Replacement: Replace batteries when the remote's response becomes sluggish or if the indicator light (if present) signals low power. Always replace both batteries at the same time with new ones of the same type (AAA).
• Cleaning: Wipe the remote control with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the electronics.
• Storage: Store the remote in a dry place, away from direct sunlight, extreme temperatures, and high humidity.
• Handling: Avoid dropping the remote control or subjecting it to strong impacts, which can cause internal damage.

5. Troubleshooting

If you encounter issues with your remote control, refer to the following troubleshooting steps:

5.1 Remote Not Responding

• Check Batteries: Ensure the batteries are correctly installed and have sufficient charge. Replace with new AAA batteries if necessary.
• Line of Sight: Ensure there are no obstructions between the remote control and the bed's control box.
• Proximity: Operate the remote within a reasonable range of the bed.

5.2 Remote Not Pairing

• Re-attempt the pairing procedure as described in Section 2.2.
• Ensure you are pressing and releasing the "Learn" or "Reset Coding" button on the control box, not holding it down.
• Confirm that your control box model is indeed MC120PR JLDP.15.020.011.

5.3 Incorrect Functionality

• Verify that your original remote had the exact same button layout and functions. Incompatible remotes may not operate correctly.
• If the issue persists, try re-pairing the remote.

6. Specifications

• Model: MC120PR JLDP.15.020.011
• Brand: Generic (Compatible with Keeson control boxes)
• Power Source: 2 x AAA Batteries (not included)
• Compatible Devices: Adjustable bed base with Keeson MC120PR JLDP.15.020.011 control box
• Max Number of Supported Devices: 1
• Color: White (as per product listing, though images show dark grey/black)
• Manufacturer: SZHKHXD
• Date First Available: August 22, 2023

7. Warranty and Support

Specific warranty information for this replacement remote control is not provided in the product details. For any warranty-related inquiries, please contact the seller directly.

For further assistance, troubleshooting beyond this manual, or to confirm compatibility, please reach out to the seller, SZHKHXD, through the platform where the product was purchased. Providing details such as your order number, photos of your bed's control box, and your original remote can help expedite support.