L6AS0F7 Dual Monitor HDMI DP KVM Switch 2x2 User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your L6AS0F7 Dual Monitor HDMI DP KVM Switch 2x2. This device allows two computers to share two monitors (one HDMI, one DisplayPort), a keyboard, mouse, and other USB 3.0 peripherals. It supports resolutions up to 4K at 60Hz, enabling efficient multi-computer workstation management.

Package Contents

1 x HDMI DP KVM Switch 2x2
2 x USB 3.0 Data Cables
1 x DC 12V Power Adapter (EU Plug)
1 x External Switch Kit
1 x User Manual

Product Overview

Familiarize yourself with the ports and controls on your KVM switch.

L6AS0F7 Dual Monitor HDMI DP KVM Switch 2x2 showing front and back panels with input/output ports.

This image displays the L6AS0F7 Dual Monitor HDMI DP KVM Switch 2x2. The top view shows the back panel with power input (DC12V), ON/OFF switch, two PC input sections (PC1 IN, PC2 IN), each featuring a DisplayPort (DP), an HDMI port, and a USB 3.0 port. On the right side of the back panel are the output ports: DP OUT and HDMI OUT. The bottom view shows the front panel with four USB 3.0 ports (labeled 1, 2, 3, 4) and a PC selection switch (SW) with indicator lights for PC1 and PC2.

Front Panel

USB 3.0 Ports (1-4): Connect your keyboard, mouse, USB drives, or other USB 3.0 peripherals.
SW (Switch Button): Press to switch between connected computers (PC1 and PC2).
PC1/PC2 Indicators: LEDs illuminate to show which computer is currently selected.

Back Panel

ON/OFF Switch: Power switch for the KVM device.
DC 12V: Power input port. Connect the provided power adapter here.
PC1 IN / PC2 IN: Input sections for connecting two computers. Each section includes:
- DP (DisplayPort): Connect to the DisplayPort output of your computer.
- HDMI: Connect to the HDMI output of your computer.
- USB 3.0: Connect to a USB 3.0 port on your computer using the provided USB 3.0 data cable. This enables keyboard, mouse, and other USB peripheral sharing.
DP OUT: Connect to your DisplayPort monitor.
HDMI OUT: Connect to your HDMI monitor.

Setup Instructions

Follow these steps to set up your KVM switch:

Power Off Devices: Ensure all computers and monitors are powered off before making any connections.
Connect Monitors: Connect your HDMI monitor to the HDMI OUT port and your DisplayPort monitor to the DP OUT port on the KVM switch.
Connect PC1:
- Connect the HDMI output of PC1 to the HDMI port in the PC1 IN section of the KVM switch.
- Connect the DisplayPort output of PC1 to the DP port in the PC1 IN section of the KVM switch.
- Connect one end of a USB 3.0 data cable to a USB 3.0 port on PC1 and the other end to the USB 3.0 port in the PC1 IN section of the KVM switch.
Connect PC2:
- Repeat the above steps for PC2, connecting its HDMI, DisplayPort, and USB 3.0 outputs to the corresponding ports in the PC2 IN section of the KVM switch.
Connect Peripherals: Connect your keyboard, mouse, and any other USB 3.0 peripherals to the USB 3.0 Ports (1-4) on the front panel of the KVM switch.
Connect Power: Connect the DC 12V power adapter to the DC 12V port on the KVM switch and plug it into a power outlet.
Power On: Turn on the KVM switch using the ON/OFF switch. Then, power on your monitors and computers.

Operating Instructions

To switch between connected computers:

Using the Front Panel Button: Press the SW (Switch Button) on the front panel of the KVM switch. The corresponding PC1 or PC2 LED indicator will light up to show the active computer.
Using the External Switch Kit: Connect the external switch kit to the designated port (if available) and press its button to switch between computers.
Hotkeys (if supported): Refer to the specific hotkey combinations in the full user manual for advanced switching options. (Note: Hotkey functionality may vary or require specific software/firmware. This KVM switch primarily uses the physical button.)

Troubleshooting

Problem	Possible Solution
No display on monitors.	Ensure all HDMI and DisplayPort cables are securely connected. Verify the KVM switch is powered on. Check if the correct input source is selected on your monitors. Try restarting the KVM switch and computers.
Keyboard or mouse not working.	Ensure the USB 3.0 data cables are connected from the KVM switch to both computers. Verify the keyboard and mouse are connected to the USB 3.0 ports on the KVM front panel. Try connecting the keyboard/mouse directly to the computer to confirm functionality. Restart the KVM switch.
Image quality issues (flickering, no 4K).	Ensure you are using high-quality HDMI 2.0 and DisplayPort 1.2 (or higher) cables. Verify your graphics card and monitors support 4K@60Hz. Check cable lengths; excessively long cables can degrade signal quality.
USB 3.0 devices not recognized.	Ensure the USB 3.0 data cables are properly connected from the KVM to the computers. Try connecting the USB device to a different USB 3.0 port on the KVM. Some high-power USB devices may require external power.

Specifications

Feature	Detail
Brand	L6AS0F7
Model	HDMI DP KVM Switch 2x2 (B0DXFDPL93)
Input Ports	2 x HDMI, 2 x DisplayPort, 2 x USB 3.0 (Type-B)
Output Ports	1 x HDMI, 1 x DisplayPort, 4 x USB 3.0 (Type-A)
Video Resolution	Up to 4K@60Hz
USB Standard	USB 3.0
Switching Method	Front panel button, External switch kit
Power Supply	DC 12V
Item Weight	50 Grams

Maintenance

To ensure the longevity and optimal performance of your KVM switch:

Keep the device in a cool, dry, and well-ventilated area.
Avoid exposing the device to direct sunlight, high temperatures, or humidity.
Clean the device with a soft, dry cloth. Do not use liquid or aerosol cleaners.
Do not attempt to open or repair the device yourself. Refer to qualified service personnel.

Warranty and Support

This product comes with a standard manufacturer's warranty. For specific warranty terms, please refer to the documentation included with your purchase or contact the retailer. For technical support or assistance, please reach out to the product manufacturer or your point of purchase.

L6AS0F7 HDMI DP KVM Switch 2x2 (B0DXFDPL93)