BAISULI Digital Display Torque Wrench AWM-R-60 Instruction Manual

Introduction

This manual provides instructions for the proper use and maintenance of your BAISULI Digital Display Torque Wrench, model AWM-R-60. This professional electronic torque wrench is designed for precise torque measurement in various applications, including automotive, bike, and general mechanical tasks. It features high accuracy, multiple operating modes, and a clear digital display for efficient and reliable operation.

Please read this manual thoroughly before operating the device to ensure safe and correct usage and to maximize the product's lifespan.

Product Overview

The BAISULI AWM-R-60 is a digital display torque wrench equipped with a 3/8 inch drive. It offers a torque range of 1.8 to 60 N.m and provides high accuracy for both clockwise and counterclockwise operations. The wrench supports four measurement units and features a dual-direction ratchet head for versatility.

Figure 1: Overall view of the BAISULI Digital Display Torque Wrench AWM-R-60.

Setup

1. Battery Installation

The device requires batteries for operation. Locate the battery compartment, typically on the handle. Insert the required batteries (usually AAA or AA, refer to the compartment label if present) ensuring correct polarity. Close the battery compartment securely.

2. Initial Power-On

Press the power button (often labeled 'P/C' or similar) to turn on the device. The digital display should illuminate.

3. Unit Selection

The wrench supports four measurement units: N-m, kgf-cm, lb-ft, and lb-in. To cycle through these units, press the 'U/S' (Unit/Set) button. Select the desired unit for your application.

Figure 2: Close-up view of the control buttons and digital display.

Operating Instructions

1. Selecting Operating Mode

The wrench offers multiple operating modes:

• Peak Mode: In this mode, you can set a target torque value. The wrench will alert you via vibration, buzzer, and LED light when the target torque is reached. This mode is suitable for applications requiring a specific, maximum torque to be applied.
• Real-time Mode (Track Mode): This mode displays real-time torque values as force is applied. It is useful for continuous monitoring of torque during tightening.
• Preset Mode: This mode allows for setting and recalling specific torque presets for repetitive tasks.

Use the 'M' (Mode) button to cycle through the available operating modes.

Figure 3: Digital display showing torque readings.

2. Setting Target Torque (Peak Mode)

1. Ensure the wrench is in Peak Mode.
2. Use the up (▲) and down (▼) arrow buttons to adjust the target torque value.
3. Confirm the setting by pressing the 'P/C' button or waiting for the display to automatically set.

3. Applying Torque

1. Attach the appropriate socket or bit to the 3/8 inch drive.
2. Place the socket onto the fastener.
3. Apply steady, increasing force to the wrench handle. Observe the digital display for real-time torque readings.
4. In Peak Mode, stop applying force when the wrench alerts you (vibration, buzzer, LED) that the target torque has been reached.
5. The wrench features a dual-direction ratchet head, allowing for both clockwise and counterclockwise operations. Adjust the ratchet direction lever as needed.

4. Data Storage

The wrench has a data storage capacity of 999 readings. Consult the full product manual or manufacturer's website for detailed instructions on how to access and manage stored data.

Maintenance

1. Cleaning

Wipe the wrench clean with a soft, dry cloth after each use. Do not use abrasive cleaners or solvents, as these can damage the display or finish. Ensure no liquids enter the electronic components.

2. Storage

Store the torque wrench in its protective case (if provided) in a dry, cool place, away from direct sunlight and extreme temperatures. Remove batteries if the wrench will not be used for an extended period to prevent leakage.

3. Battery Replacement

When the battery indicator on the display shows low power, replace the batteries promptly to ensure accurate readings and continuous operation. Follow the battery installation steps outlined in the Setup section.

4. Calibration

Digital torque wrenches require periodic calibration to maintain accuracy. The frequency of calibration depends on usage and environmental conditions. It is recommended to have the wrench calibrated by a qualified service center annually or after significant impact or heavy use. Refer to the manufacturer's guidelines for specific calibration recommendations.

Troubleshooting

• Display Not Working:
  - Check battery installation and ensure correct polarity.
  - Replace batteries with fresh ones.
  - Ensure the power button is pressed firmly.
• Inaccurate Readings:
  - Ensure the correct unit of measurement is selected.
  - Verify that the wrench is properly calibrated. If not, consider professional calibration.
  - Avoid applying sudden jerks; apply force smoothly and steadily.
  - Ensure the fastener is clean and free of debris.
• No Buzzer/LED Alert in Peak Mode:
  - Check if the wrench is correctly set to Peak Mode.
  - Ensure the target torque value is set appropriately and not exceeded too quickly.
  - Check battery level.
• Wrench Not Turning:
  - Ensure the ratchet direction lever is engaged correctly for the desired direction (clockwise or counterclockwise).
  - Check for any obstructions in the ratchet mechanism.

If problems persist after attempting these troubleshooting steps, contact customer support or a qualified service technician.

Specifications

Figure 4: Key specifications of the AWM-R-60 torque wrench.

Warranty Information

Specific warranty details for the BAISULI Digital Display Torque Wrench AWM-R-60 are not provided in this document. For information regarding warranty coverage, duration, and claims, please refer to the product packaging, the manufacturer's official website, or contact the seller directly at the point of purchase.

Customer Support

If you have any questions, require technical assistance, or encounter issues not covered in this manual, please contact the retailer or manufacturer for support. Keep your purchase receipt and product model number handy when contacting support.