MakeFit L1001 All Metal Dual Shower Head Combo Instruction Manual

Introduction

The MakeFit L1001 All Metal Dual Shower Head Combo is designed to provide a versatile and durable showering experience. This system includes a 10-inch high-pressure rain shower head, a handheld spray, a curved extension arm, and a 71-inch extra-long shower hose. Constructed from rust-proof and break-resistant metal, this system is built for longevity and reliable performance.

Package Contents

Verify that all components are present before beginning installation:

• 10-Inch Rainfall Shower Head x 1
• Handheld Shower Wand x 1
• Adjustment Curved Shower Extension Arm x 1
• 70.8-Inch Shower Hose x 1
• Adhesive Shower Holder x 2 (one extra in case of damage)
• Wrench x 1
• Teflon Tape x 1

Figure 1: Exploded view of shower head components.

Setup and Installation

This dual shower head system is designed for quick installation on any standard G1/2" shower arm. Follow these steps for proper setup:

1. Prepare the Shower Arm: Ensure your existing shower arm is clean and free of debris. Apply Teflon tape to the threads of the shower arm to prevent leaks.
2. Install the Diverter: Screw the diverter onto the shower arm. Hand-tighten first, then use the provided wrench for a secure fit.
3. Attach the Curved Extension Arm: Connect the curved extension arm to the diverter. Ensure the connection is tight to prevent water leakage.
4. Install the Rain Shower Head: Screw the 10-inch rainfall shower head onto the curved extension arm. Hand-tighten, then use the wrench for final tightening.
5. Connect the Handheld Hose: Attach one end of the 70.8-inch shower hose to the diverter's handheld outlet and the other end to the handheld shower wand. Ensure gaskets are properly seated in the hose connections.
6. Mount the Handheld Holder: Clean and dry the desired wall location for the adhesive shower holder. Peel off the film from the back of the holder and firmly press it onto the wall. Allow 8 hours for the adhesive to set before placing the handheld shower wand in it.

Operating Instructions

The MakeFit L1001 offers flexible showering options:

• Rainfall Spray: The 10-inch rainfall shower head provides wide coverage and an even water flow for a full-body soak.
• Handheld Spray: The metal handheld shower head offers precise, targeted rinsing, ideal for specific areas, cleaning, or bathing children and pets.
• Dual Mode: The diverter allows you to use the rain shower and handheld shower separately or simultaneously for maximum coverage.

To switch between modes, rotate the diverter knob located on the main unit. The curved extension arm is height and angle adjustable, allowing you to customize the shower experience to suit different users and preferences.

Figure 2: Rainfall shower mode in operation.

Figure 3: Handheld shower mode for targeted rinsing.

Figure 4: Both rainfall and handheld showers operating simultaneously.

Maintenance

To ensure optimal performance and longevity of your MakeFit shower system, regular maintenance is recommended:

• Cleaning Nozzles: The anti-clog silicone nozzles can be easily cleaned by gently rubbing them to dislodge any mineral buildup. This helps maintain a steady, high-pressure spray.
• Surface Cleaning: Wipe down the metal surfaces with a soft cloth and mild soap or a non-abrasive bathroom cleaner. Avoid harsh chemicals or abrasive scrubbers that could damage the finish.
• Hose Inspection: Periodically check the shower hose for any signs of wear, kinks, or leaks. Replace if necessary.

Troubleshooting

If you encounter any issues with your MakeFit shower system, refer to the following common solutions:

• Low Water Pressure: Check if the water supply valves are fully open. Ensure the shower head nozzles are clear of mineral buildup (refer to Maintenance section). Verify that the hose is not kinked.
• Leaks at Connections: Tighten all connections using the provided wrench, ensuring Teflon tape is properly applied to threaded joints. Check for damaged gaskets and replace if necessary.
• Diverter Not Switching Properly: Ensure the diverter knob is fully rotated to the desired position. If it feels stiff, a small amount of silicone grease can be applied to the moving parts (ensure it is safe for plumbing).

If problems persist, please contact MakeFit customer support for further assistance.

Specifications

Warranty Information

Specific warranty details for the MakeFit L1001 Dual Shower Head Combo are not provided in this document. Please refer to the product packaging or contact MakeFit customer support for comprehensive warranty information.

Customer Support

For further assistance, technical support, or to inquire about replacement parts, please contact MakeFit customer service or visit the official MakeFit store:

• Online Store: MakeFit Store on Amazon
• Manufacturer: Xia Men Yi Fang Yun Science and Technology Ltd.