WinZo Modern Tankless Smart Toilet

Product Overview

The WinZo Modern Tankless Smart Toilet SM8008 is designed to provide an advanced and hygienic bathroom experience. It integrates several smart features for convenience and cleanliness.

• Smart Automatic Flushing: Features auto open/close upon approach and automatic flushing after use. Flushing can also be controlled via remote, side knob, or foot kick.
• Foam Shield & Auto Deodorization: Generates a foam layer to prevent splashing, block odors, and resist waste adherence.
• Air Purification System: A built-in filter box absorbs unpleasant odors, maintaining a fresh environment.
• Heated Seat: Offers 4 adjustable temperature levels for comfort, especially during colder seasons.
• Hygienic Cleaning & Drying: Includes female cleaning, hip cleaning, massage cleaning, and self-cleaning nozzles. Features warm air drying for a complete experience.
• Auto LED & Nightlight: Provides gentle illumination for nighttime use and features a soft-close seat for quiet operation.

Setup and Installation

Proper installation is crucial for the optimal performance of your WinZo Smart Toilet. Please follow these steps carefully. It is recommended to consult a professional plumber if you are unsure about any step.

Pre-Installation Checks

1. Clean the ground thoroughly and ensure it is dry before installation.
2. Verify that the ground is horizontal using a level.
3. Ensure the sewer pipe is unobstructed.
4. Measure the rough-in distance. It should be at least 12 inches.
5. Measure the water pressure. It should be over 0.14MPa with a flow rate over 18L/min.

Installation Steps

1. Wrap the raw material belt (Teflon tape) around the interface of the angle valve to ensure a watertight seal.
2. Install the angle valve onto the water supply line.
3. Drain any residual water from the angle valve before proceeding.
4. Reinstall the constant flow valve into the angle valve.
5. Install expansion screws into the floor flange.
6. Mount the flange at the drain opening, securing it with the expansion screws.
7. Attach the wax ring to the bottom of the smart toilet, ensuring it aligns with the drain hole.
8. Carefully align the toilet with the flange and screws on the floor.
9. Install the flat washer and nut to secure the toilet to the floor flange.
10. Settle the upper part of the toilet onto the base, ensuring all connections are secure.
11. Connect the water inlet pipe to the angle valve. Ensure the braided tube is not bent. Open the angle valve to the maximum and check for any water leaks.
12. Plug the toilet into a 110V power outlet to power it on.

Installation Video Guide

This video demonstrates the step-by-step installation process for the WinZo Smart Toilet, including preparing the site, installing the angle valve, mounting the flange, and connecting the water inlet pipe.

Installation Components

Image showing various components included for installation, such as the angle valve, floor mounted bolts, and the toilet installation manual.

Operating Instructions

The WinZo Smart Toilet offers various automatic and user-controlled functions for a personalized experience.

Automatic Functions

• Auto Open/Close: The toilet seat and lid will automatically open when you approach and close after you leave.
• Auto Flush: The toilet automatically flushes after you leave the seat.
• Foot Kick: A gentle foot kick can activate the auto open/close or flush functions.

This image illustrates the automatic opening feature when approaching the toilet and the foot kick function to open the seat cover or flush.

Controls: Remote and Side Knob

The toilet can be controlled using the wireless remote or the side knob and buttons located on the unit.

This image highlights the side knob and buttons for various functions, the LED display, the foam shield feature, and the night light.

Cleaning Functions

• Female Cleaning: Gentle front wash for feminine hygiene.
• Hip Cleaning: Rear wash for thorough cleansing.
• Massage Cleaning: Provides a pulsating water stream for a massage effect.
• Self-Cleaning Nozzles: The nozzles clean themselves before and after each use.
• UV-C Sterilization: The nozzles are sterilized with UV-C light for enhanced hygiene.

This image shows the self-cleaning nozzles with UV-C sterilization and illustrates various cleaning modes including rotary washing, hip washing, female washing, and self-cleaning.

Comfort Features

• Heated Seat: Adjust the seat temperature to one of 4 levels for optimal comfort.
• Warm Air Drying: After cleaning, warm air drying is available with 4 temperature levels and 3 wind settings.
• Nightlight: A built-in LED nightlight provides soft illumination for convenience during the night.

This image displays the comfort heated seat with adjustable temperature levels and the instant warm air dryer with its temperature and wind settings.

Operational Video Guide

This video showcases the automatic functions of the WinZo Smart Toilet, including auto open, foot kick to open the seat, remote controls, side knob and buttons, soft close seat, LED display, air fresh system, heated seat, foam shield, live water instant heating, self-cleaning nozzles, varied cleaning modes, infrared ray, warm air drying, U-V functions, and powerful flush.

Maintenance

Regular maintenance ensures the longevity and hygienic performance of your smart toilet.

• Nozzle Cleaning: The self-cleaning nozzles automatically rinse before and after each use. Periodically inspect the nozzles for any buildup and clean manually with a soft brush if necessary.
• Exterior Cleaning: Wipe the exterior surfaces of the toilet with a soft, damp cloth and a mild, non-abrasive cleaner. Avoid harsh chemicals that could damage the finish.
• Air Fresh System Filter: The air fresh system contains a filter. Refer to the detailed product manual for instructions on how to access and replace or clean this filter periodically to maintain optimal odor absorption.
• Foam Shield System: Ensure the foam shield dispenser is refilled as needed with compatible foam solution.
• Power Off for Extended Absence: If the toilet will not be used for an extended period, it is advisable to turn off the water supply and unplug the unit.

Troubleshooting

If you encounter any issues with your WinZo Smart Toilet, please refer to the following common troubleshooting tips. For more complex problems, contact customer support.

• No Power: Check if the power cord is securely plugged into a 110V outlet. Verify that the outlet has power by testing it with another device.
• No Water Flow/Weak Flush: Ensure the angle valve is fully open. Check the water pressure (should be over 0.14MPa). Inspect the water inlet pipe for kinks or blockages.
• Automatic Functions Not Responding: Ensure the sensor is clean and unobstructed. Check the remote control batteries if using the remote.
• Heated Seat Not Warming: Verify that the heated seat function is activated via the remote or side controls. Check the temperature setting.
• Leaking: Immediately turn off the water supply at the angle valve. Check all connections for tightness, especially the water inlet pipe and angle valve. Ensure the wax ring is properly seated.

Specifications

Diagram illustrating the product dimensions, including depth, width, height, rough-in, and seat height.

Warranty and Support

For warranty information, product support, or to purchase replacement parts, please contact WinZo customer service. Keep your purchase receipt as proof of purchase.

WinZo is committed to delivering high-quality and innovative bathroom products. Our range of toilets is designed and manufactured to meet strict industry standards.

For assistance, please visit the WinZo Store on Amazon or refer to the contact information provided in your product packaging.