Introduction
The North Spore BoomRoom II is an automated mushroom grow tent system designed for efficient indoor mycology. This system provides controlled humidity and fresh air exchange (FAE) to optimize mushroom cultivation. It features a 5-rack chamber, offering significant vertical growing space.
This manual provides detailed instructions for the assembly, operation, and maintenance of your BoomRoom II kit to ensure successful mushroom growth.
Figure 1: Fully assembled BoomRoom II Mushroom Grow Tent with humidifier.
Setup and Assembly
Carefully unpack all components and verify against the packing list. Assembly typically involves constructing the frame, attaching the tent cover, and integrating the humidity and air exchange systems.
- Frame Assembly: Assemble the metal frame according to the included diagrams. Ensure all poles are securely connected.
- Tent Cover Installation: Carefully slide the clear vinyl tent cover over the assembled frame. Exercise caution to avoid tearing the material.
- Shelf Installation: Place the 5 reinforced racks onto the frame at desired heights.
- Humidifier Placement: Position the Myco-Mister II humidifier outside the tent, ensuring it is on a stable, level surface.
- Duct Connection: Connect the humidifier's output duct to the designated port on the tent cover. Secure the connection to prevent humidity leaks.
- FAE Fan Setup: Install the Fresh Air Exchange (FAE) fan. Connect its ducting to the appropriate tent port.
- Spore Floor Tray: Place the "Spore Floor" bottom tray inside the tent to collect any runoff.
Figure 2: Detail of the duct connection for humidity or FAE.
Figure 3: Myco-Mister II humidifier unit.
Video 1: Official North Spore BoomRoom II setup and feature overview. This video demonstrates the assembly process and highlights key functionalities of the grow tent system.
Operating Instructions
The BoomRoom II is designed for automated environmental control. Proper operation involves setting the humidity and managing fresh air exchange.
Humidity Control (Myco-Mister II)
- Fill the Myco-Mister II reservoir with distilled water.
- Connect the humidifier to a power source.
- Adjust the dial on the humidifier to achieve the desired relative humidity (RH) level, typically 90%+ for mushroom pinning. Monitor the RH inside the tent using a hygrometer (not included).
Fresh Air Exchange (FAE)
- Connect the FAE fan to a power source.
- The FAE fan cycles out stale CO2, which is crucial for proper mushroom development. Operate the fan periodically or continuously as required by your specific mushroom species.
- The system is designed to run with negative pressure, helping to filter spores and maintain a clean environment.
Figure 4: Mushroom blocks arranged on the internal shelves of the grow tent.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your BoomRoom II.
- Humidifier Cleaning: Clean the Myco-Mister II regularly to prevent mineral buildup and ensure efficient operation. Follow the humidifier's specific cleaning instructions.
- Tent Cleaning: Wipe down the interior and exterior of the tent cover with a mild disinfectant solution as needed to prevent contamination.
- Spore Floor Tray: Empty and clean the "Spore Floor" bottom tray regularly to manage runoff and prevent spore accumulation.
- Filter Replacement: Check and replace any air filters associated with the FAE system as recommended by the manufacturer.
Troubleshooting
This section addresses common issues you might encounter with your BoomRoom II.
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Humidity in Tent | Humidifier reservoir empty, humidifier malfunction, duct not sealed, FAE fan running too frequently. | Refill humidifier. Check humidifier operation. Ensure all duct connections are secure. Adjust FAE fan timer/frequency. |
| Excessive Condensation | Insufficient FAE, humidifier setting too high, ambient temperature fluctuations. | Increase FAE fan frequency or duration. Lower humidifier setting slightly. Ensure stable room temperature. |
| Poor Mushroom Growth / Leggy Stems | Insufficient fresh air exchange (high CO2 levels). | Increase FAE fan operation. Ensure FAE fan is functioning correctly. |
| Tent Cover Damage (e.g., tear) | Improper handling during assembly or relocation. | Use a durable repair kit for vinyl or contact North Spore support for replacement parts. Handle with care during assembly. |
Specifications
| Feature | Detail |
|---|---|
| Brand | North Spore |
| Model | BoomRoom II |
| Chamber Volume | 18 cubic feet |
| Frame Material | Metal |
| Inner Material | PVC |
| Number of Racks | 5 |
| Color | Clear |
| GTIN/UPC | 810107471418 |
Warranty Information
North Spore products are designed for quality and durability. For specific warranty details regarding your BoomRoom II Automated Mushroom Grow Tent Kit, please refer to the documentation included with your purchase or visit the official North Spore website. Typically, products are covered against manufacturing defects for a specified period from the date of purchase.
Keep your proof of purchase for any warranty claims.
Customer Support
If you encounter any issues or have questions not covered in this manual, please contact North Spore customer support.
- Online Support: Visit the North Spore Store on Amazon or their official website for FAQs and contact options.
- Email: Refer to your product packaging for direct email support.
- Phone: Refer to your product packaging for direct phone support.
When contacting support, please have your product model (BoomRoom II) and purchase information ready.