TollCor CS-CNS990VX

User Manual: TollCor 2600mAh/14.4V Replacement Battery

Model: CS-CNS990VX

1. Product Overview

This document provides essential information for the safe and effective use of the TollCor 2600mAh/14.4V Li-ion replacement battery, model CS-CNS990VX. This battery is designed as a direct replacement for specific Mamibot ExVac robot vacuum cleaner models.

TollCor 2600mAh/14.4V Li-ion replacement battery

Image: The TollCor 2600mAh/14.4V Li-ion replacement battery, showing its blue casing and black label with specifications and warnings.

2. Compatibility

This replacement battery is compatible with the following Mamibot ExVac robot vacuum cleaner models:

  • Mamibot ExVac 680S
  • Mamibot ExVac 880
  • Mamibot EXVAC660
  • Mamibot EXVAC680S
  • Mamibot EXVAC880

Always verify the model number of your device before purchasing and installing a replacement battery.

3. Safety Information and Warnings

WARNING: To reduce the risk of fire or burns, read and follow all instructions carefully.

  • DO NOT attempt to disassemble, open or service the battery pack.
  • REPLACE ONLY with the battery pack designated for this product.
  • DO NOT crush, puncture, short external contacts or dispose of in fire or water.
  • DO NOT store above 60°C (140°F).
  • Dispose of used batteries according to local regulations.
  • Keep out of reach of children.
Battery label with safety warnings

Image: Close-up view of the battery label, highlighting important safety warnings and specifications.

4. Installation Instructions

Follow these general steps for replacing the battery in your Mamibot ExVac robot vacuum. Specific steps may vary slightly depending on your exact model. Refer to your robot vacuum's original user manual for detailed instructions if available.

  1. Power Off and Unplug: Ensure your robot vacuum is completely powered off and unplugged from its charging base or power adapter.
  2. Locate Battery Compartment: Turn the robot vacuum upside down. The battery compartment is typically located on the underside, often secured by screws or a latch.
  3. Open Compartment: Use a screwdriver (if necessary) to remove any screws securing the battery compartment cover. Carefully open or remove the cover.
  4. Disconnect Old Battery: Gently disconnect the old battery from its connector. Note the orientation of the connector before removal.
  5. Remove Old Battery: Carefully lift the old battery out of the compartment.
  6. Insert New Battery: Place the new TollCor replacement battery into the compartment, ensuring it fits snugly.
  7. Connect New Battery: Align the connector of the new battery with the port inside the compartment and firmly push it in until it clicks into place.
  8. Battery connector close-up

    Image: Close-up of the battery's electrical connector, showing the black and red wires and the plug design.

  9. Close Compartment: Replace the battery compartment cover and secure it with screws if applicable.
  10. Initial Charge: Place the robot vacuum back on its charging base or connect it to its power adapter for an initial full charge before first use.

5. Operating and Maintenance Tips

To maximize the lifespan and performance of your new battery:

  • Regular Charging: Keep the robot vacuum on its charging base when not in use to ensure the battery remains charged.
  • Avoid Deep Discharge: Do not allow the battery to completely drain before recharging.
  • Storage: If storing the robot vacuum for an extended period, ensure the battery is partially charged (around 50%) and store it in a cool, dry place. Recharge every few months to prevent deep discharge.
  • Temperature: Avoid operating or storing the battery in extreme temperatures (very hot or very cold).
  • Cleaning: Keep the battery contacts clean and free of dust or debris.

6. Troubleshooting

If you encounter issues after replacing the battery, consider the following:

ProblemPossible CauseSolution
Robot vacuum does not power on.Battery not properly connected; Battery not charged.Check battery connection; Ensure battery is fully charged.
Short run time after charging.Battery not fully charged; Battery degradation (unlikely for new battery).Ensure full charge cycle; Contact support if issue persists.
Charging indicator not working.Poor contact with charging base; Faulty charging base/adapter.Clean charging contacts; Test charging base/adapter.

If troubleshooting steps do not resolve the issue, please refer to the "Warranty and Support" section.

7. Specifications

Key technical specifications for the TollCor CS-CNS990VX replacement battery:

  • Battery Type: Li-ion
  • Voltage: 14.4V
  • Capacity: 2600mAh / 37.44Wh
  • Model Number: CS-CNS990VX
  • Dimensions: 69.50 x 37.00 x 37.00mm (2.74 x 1.46 x 1.46 inches)
  • Gross Weight: 270g (9.5 ounces)
  • Manufacturer: TollCor
  • Standard: GB 31241-2014
  • Part Number: CONG1002 (as per label)

For more information, you may refer to the manufacturer's details on the battery label, which sometimes includes links like www.cameronsino.com.

8. Warranty and Support

TollCor provides the following support for this product:

  • Money Back Guarantee: 30-day money back policy.
  • Warranty: 365-day warranty from the date of purchase.
  • Customer Support: 24-hour timely feedback for inquiries.

For any questions, concerns, or warranty claims, please contact the seller through the platform where the product was purchased. Please have your order details and product model number (CS-CNS990VX) ready when contacting support.

© 2024 TollCor. All rights reserved. This manual is for informational purposes only.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.