S116 GPS Drone User Manual

Introduction

This user manual provides comprehensive instructions for the safe operation, maintenance, and troubleshooting of your S116 GPS Drone. Please read this manual thoroughly before operating the drone to ensure proper use and to maximize your flying experience. Keep this manual for future reference.

What's in the Box

Upon unboxing, verify that all components listed below are present and in good condition:

• S116 GPS Drone
• Screen Controller
• 2 x Drone Batteries
• Carrying Case
• Screwdriver
• Spare Propellers (typically 4)
• USB Charging Cable (for drone batteries and controller)
• User Manual (this document)

Figure 1: All components included in the S116 GPS Drone package, including the drone, screen controller, two batteries, carrying case, screwdriver, and spare propellers.

Key Product Features

• Screen Controller: Integrated display on the remote control for direct FPV viewing without needing a smartphone.
• Dual Battery System: Includes two batteries for extended flight time and convenience.
• Active Obstacle Avoidance: Sensors detect and help the drone navigate around obstacles, enhancing safety.
• One-Key Take Off/Landing: Simplifies flight initiation and conclusion with a single button press.
• Built-in GPS System: Provides stable hovering, precise positioning, and features like Return-to-Home.
• Brushless Motor: Offers improved efficiency, power, and durability.
• Dual Cameras: Allows for versatile aerial photography and video recording with remote switching.
• Optical Flow Hover: Maintains stable flight both indoors and outdoors, especially at lower altitudes.

Components Overview

S116 Drone

Figure 2: The S116 drone, highlighting its optical flow sensor for stable hovering and obstacle avoidance capabilities.

The S116 drone features a robust design with brushless motors for stable flight. It includes an optical flow sensor for precise indoor and low-altitude hovering, and an obstacle avoidance system for enhanced safety during flight.

Dual Camera System

Figure 3: Close-up of the S116 drone's dual camera system, showing the adjustable angle and remote switching capability.

Equipped with dual cameras, the S116 allows for versatile aerial perspectives. Users can remotely switch between cameras and adjust the angle up to 90 degrees for optimal photo and video capture.

Screen Controller

Figure 4: Detailed diagram of the S116 Screen Controller, indicating the function of each button and joystick.

The Screen Controller provides an integrated display for real-time video transmission. Key controls include:

• Left Joystick: Throttle (up/down), Headless/Backward (left/right)
• Right Joystick: Direction lever (forward/backward, left/right)
• One Click Lifting: Initiates automatic take-off.
• One Click Emergency Stop: Immediately stops motors in an emergency.
• Obstacle Avoidance: Toggles obstacle avoidance system.
• Take Photos/View Photos: Captures still images and accesses gallery.
• Recording/Viewing Videos: Starts/stops video recording and accesses video library.
• Screen Switch: Toggles display modes or camera views.
• One Click Reset: Resets drone settings.
• Speed Switching: Adjusts flight speed modes.
• Camera Up/Down: Adjusts camera tilt angle.
• Choose Up/Select Below: Navigation buttons for menu.
• Play/Main Interface: Toggles between video playback and main flight interface.
• LCD Display Screen: Shows real-time video feed and flight data.

Setup Guide

1. Charge Batteries: Fully charge both drone batteries and the controller battery using the provided USB charging cable. The charging indicator will change when charging is complete.
2. Install Drone Battery: Insert a fully charged battery into the drone's battery compartment until it clicks securely into place.
3. Install Propellers (if necessary): If propellers are not pre-installed, attach them according to the markings (e.g., A and B) on the propellers and motor arms. Ensure they are tightened securely.
4. Power On Drone: Place the drone on a flat, level surface. Press and hold the power button on the drone until the indicator lights illuminate.
5. Power On Controller: Press and hold the power button on the Screen Controller until the screen turns on.
6. Pairing: The drone and controller should automatically pair. If not, follow the pairing instructions in the Operating section.
7. Calibration: Perform compass and gyroscope calibration as described in the Operating section before your first flight and if you change flight locations significantly.

Operating Instructions

Pre-Flight Checklist

• Ensure all batteries are fully charged.
• Check propellers for damage and ensure they are securely attached.
• Select an open, clear area free from obstacles, people, and animals.
• Verify GPS signal strength (if flying outdoors).
• Perform necessary calibrations.

Basic Flight Operations

1. Power On & Pairing:
   • Turn on the drone first, then the controller.
   • Wait for the drone and controller to connect. Indicator lights will confirm connection.
2. Calibration:
   • Compass Calibration: Follow on-screen prompts or manual instructions (typically rotating the drone horizontally and vertically). Essential for accurate GPS positioning.
   • Gyroscope Calibration: Place the drone on a flat surface and perform the calibration sequence (often by moving both joysticks to a specific corner).
3. One-Key Take Off:
   • Press the "One Click Lifting" button on the controller. The drone will automatically take off and hover at a safe altitude.
4. Flight Controls:
   • Left Joystick (Throttle): Push up to ascend, pull down to descend.
   • Left Joystick (Yaw): Push left/right to rotate the drone counter-clockwise/clockwise.
   • Right Joystick (Pitch/Roll): Push up/down to fly forward/backward. Push left/right to fly left/right.
5. Obstacle Avoidance:
   • The drone's sensors will automatically detect obstacles and attempt to avoid them. This feature can be toggled on/off via the controller.
6. GPS Functions:
   • Altitude Hold: The drone will maintain a stable altitude automatically.
   • Position Hold: With sufficient GPS signal, the drone will maintain its position.
   • Return-to-Home (RTH): Press the RTH button. The drone will return to its take-off point. Ensure a clear path for RTH.
7. Camera Operation:
   • Take Photo: Press the dedicated photo button on the controller.
   • Start/Stop Video: Press the dedicated video button on the controller.
   • Camera Angle Adjustment: Use the camera up/down buttons to adjust the camera's tilt.
8. One-Key Landing:
   • Press the "One Click Lifting" button again (or a dedicated landing button if available). The drone will automatically descend and land.
9. Emergency Stop:
   • In an emergency, press the "One Click Emergency Stop" button to immediately cut power to the motors. Use with caution as the drone will drop.

Maintenance

• Cleaning: Regularly wipe the drone and controller with a soft, dry cloth. Avoid using harsh chemicals or solvents. Ensure no dust or debris accumulates in the motors or camera lens.
• Propeller Inspection: Before each flight, inspect propellers for cracks, bends, or chips. Replace damaged propellers immediately using the provided screwdriver and spare parts.
• Battery Care:
  • Do not overcharge or over-discharge batteries.
  • Store batteries in a cool, dry place away from direct sunlight and extreme temperatures.
  • If storing for extended periods, charge batteries to approximately 50-60% capacity.
• Motor Maintenance: Keep motors free from dust, hair, and other obstructions. Do not attempt to lubricate motors unless specified by the manufacturer.
• Storage: When not in use, store the drone and all accessories in the provided carrying case to protect them from damage.

Troubleshooting

For issues not listed here, please refer to the official product support channels or contact customer service.

Specifications

Warranty and Support

The S116 GPS Drone comes with a standard manufacturer's warranty. Please refer to the warranty card included in your package for specific terms and conditions, including warranty duration and coverage details.

For technical support, troubleshooting assistance, or warranty claims, please contact enttgo customer service through their official website or the contact information provided with your purchase. Always provide your product model (S116) and purchase details when seeking support.

For additional protection, consider purchasing an extended protection plan if available, such as those offered by Amazon or third-party providers.