ULANZI SL02 Mini Flash Speedlite and Video Light Instruction Manual

1. Introduction

The ULANZI SL02 Mini Flash Speedlite and Video Light is a compact and lightweight external lighting solution designed for various cameras equipped with a single-contact hot shoe. It offers both flash and continuous video light modes, providing adjustable brightness levels to enhance photographic and videographic results in diverse shooting conditions.

Figure 1: ULANZI SL02 Mini Flash Speedlite and Video Light.

2. Package Contents

• ULANZI SL02 Mini Flash Speedlite and Video Light × 1
• User Manual × 1

Note: Charger and charging cable are not included in the package.

3. Compatibility

The ULANZI SL02 is designed for cameras featuring a single-contact hot shoe. Please verify your camera's hot shoe type before use.

3.1 Compatible Cameras

• SONY: A7III, A7IV, A7R5, A7RIII, A7RIV, A9, A7RII/V4.0, A7R, A6400, RX10, ZV-1, ZV-E10
• CANON: 5DIII, 5DIV, 70D, 80D, 1DX, 850D, 760D, 5DII, 7DII, 6DII, 6D, 800D, 90D, 600D, 7D, M6, M5, M3, EOS RP, EOS R, R5, 60D
• NIKON: D800, D780, D5, D4, D500, D610, D750, D700, D300S, D3300, D3100, D5300, D5200, D5000, 27II, 26, Z8, ZFC, D200, D60, D5100, D7500, D7100
• FUJI: X-Pro2, X-T20, X-T2, X-T1, GFX50s, GFX50R, X-T30, X-T4, X-T3, X-Pro1, X-T10, X-E1, X-T5, X-M5
• PANASONIC: GH4, LX100, GF1, G85, GX85, FZ2500GX, S1R, GH5, G7
• LEICA: SL1, M10, Q2, TYP601, CL, SL2
• PENTAX: K-3I1, 645Z, KP, K-70, K-S2, K-1, K50
• OLYMPUS: E-M1, PRN-F, E-M10II, E-M10III, E-PL8, E-P5, E-M5I

3.2 Incompatible Cameras

• SONY: ZV-1F, ZV1-F, A9III, A99, A77, A350, Zv1 Mark 2
• CANON: 3000D, 1500D, 200DII, R50
• FUJI: X-A3, X100F, X100T

Cameras that do not feature a single-contact hot shoe are not compatible.

Figure 2: Illustration of compatible (with electrical contacts) and incompatible (without electrical contacts) hot shoe types.

4. Setup

4.1 Charging the Device

The SL02 features a built-in 250mAh 3.7V polymer battery. Use a Type-C 5V 1A charger (not included) to charge the device. A full charge takes approximately 1 hour. The device can be used while charging.

• Charging Indicator: A red light indicates charging, and a green light indicates a full charge.
• Battery Life: Provides up to 500 full-power flashes or 1 hour and 25 minutes of continuous use in video light mode.

Figure 3: Charging the ULANZI SL02 via Type-C port. Red light indicates charging, green light indicates fully charged.

4.2 Attaching to Camera

Slide the SL02's hot shoe mount into your camera's hot shoe slot until it clicks securely into place. Ensure a firm connection for proper functionality.

5. Operating Instructions

5.1 Power On/Off

Press and hold the ON/OFF button to power the device on or off.

5.2 Switching Between Flash and Video Light Modes

Long-press the MODE button to switch between Flash Mode and Video Light Mode.

5.3 Adjusting Brightness/Power Levels

In either Flash Mode or Video Light Mode, short-press the MODE button to cycle through the four available brightness/power levels: 1/1 (full power), 1/2, 1/4, and 1/8.

Figure 4: Long-press MODE to switch modes, short-press MODE to adjust brightness levels. Recycling times for flash mode are also shown.

5.4 Flash Mode Operation

• Guide Number (GN): GN8 at ISO100.
• Color Temperature: 6500±300K.
• Color Rendering Index (CRI): 97.
• Shutter Speed: For optimal results, ensure the camera's shutter speed does not exceed 1/250s.

Figure 5: Visual representation of flash output at 1/1, 1/2, 1/4, and 1/8 power levels.

5.5 Video Light Mode Operation

• Continuous Color Temperature: 5600K.
• Color Rendering Index (CRI): 95.
• Illuminance Levels: 200 lux at 0.3m, 81.4 lux at 0.5m, and 21.9 lux at 1m.
• Power Output: 1W.

Figure 6: The ULANZI SL02 providing continuous illumination in video light mode.

5.6 Specific Instructions for FUJI Cameras

To use the SL02 external flash with FUJI cameras, follow these steps:

1. Access the camera's flash settings. Set the flash sync setting to "M" (Manual mode). The flash will then fire in manual mode.
2. If the flash still does not fire, it may be due to the shutter type. Change the shutter type from electronic to mechanical. Then, adjust the flash settings and change the flash setting from OFF to M. Focus the camera, and then switch the flash back to manual mode.

6. Maintenance

• Keep the device clean by wiping it with a soft, dry cloth.
• Avoid exposing the device to water or excessive moisture.
• Store the device in a cool, dry place when not in use.
• Do not attempt to disassemble or repair the device yourself. Contact customer support for assistance.

7. Troubleshooting

7.1 Flash Not Firing / Video Light Not Illuminating

• Check Compatibility: Ensure your camera has a single-contact hot shoe and is listed as compatible.
• Secure Connection: Verify the SL02 is fully inserted and securely seated in the camera's hot shoe.
• Battery Level: Check if the device is sufficiently charged. Recharge if the indicator light is off or red.
• Mode Selection: Confirm the correct mode (Flash or Video Light) is selected.
• FUJI Camera Settings: If using a FUJI camera, refer to Section 5.6 for specific flash settings.

7.2 Short Battery Life

• Ensure the device is fully charged before use (approximately 1 hour).
• Battery performance may decrease over time with repeated charging cycles.
• Operating at full power (1/1) in flash mode or continuously in video light mode will consume battery faster.

8. Specifications

9. Warranty and Support

For warranty information, technical support, or any issues encountered during the use of your ULANZI SL02 Mini Flash Speedlite and Video Light, please contact ULANZI customer service through the retailer where the product was purchased or visit the official ULANZI website for support resources.