LeisureMod Modern Dining Chair (Model CDWN-18LBR) Instruction Manual

Introduction

Thank you for choosing the LeisureMod Modern Dining Chair. This manual provides essential information for the safe assembly, proper use, and effective maintenance of your new chair. Please read these instructions thoroughly before assembly and retain them for future reference.

Image: Four LeisureMod Modern Dining Chairs arranged around a dining table in a contemporary kitchen environment.

Safety Information

• Weight Capacity: This chair is designed to support a maximum weight of 300 pounds (approximately 136 kg). Do not exceed this limit to prevent damage or injury.
• Assembly: Ensure all parts are securely fastened before using the chair. Periodically check and tighten all connections.
• Placement: Place the chair on a flat, stable surface. Avoid placing it on uneven ground or near heat sources.
• Children: Keep small parts away from children during assembly. Do not allow children to climb or play on the chair unsupervised.
• Movement: Always lift the chair when moving it to prevent damage to the chair or your flooring. Avoid dragging.

Package Contents

Before beginning assembly, verify that all components listed below are present and undamaged. If any parts are missing or damaged, please contact customer support.

• Chair Seat (1)
• Chair Backrest (1)
• Legs (4)
• Hardware Pack (Screws, Washers, Allen Wrench)

Setup and Assembly Instructions

Follow these steps carefully to assemble your dining chair. It is recommended to assemble the chair on a soft, clean surface to prevent scratches.

1. Step 1: Prepare Components. Unpack all parts and lay them out on a protected surface. Identify the chair seat, backrest, legs, and hardware.
2. Step 2: Attach Legs to Seat. Carefully align each leg with the pre-drilled holes on the underside of the chair seat. Secure each leg using the provided screws and washers. Do not fully tighten the screws yet.
3. Step 3: Attach Backrest. Position the backrest against the rear of the chair seat, aligning the mounting points. Secure the backrest to the seat and legs using the remaining screws.
4. Step 4: Final Tightening. Once all components are loosely assembled, place the chair upright on a flat surface. Apply gentle downward pressure to ensure all parts are seated correctly, then fully tighten all screws using the Allen wrench. Do not overtighten.
5. Step 5: Check Stability. Gently rock the chair to ensure it is stable and does not wobble. If wobbling occurs, re-check all connections and adjust as necessary.

Image: Rear view of the dining chair, illustrating the connection points for the backrest and the angled leg design.

Operating Instructions (Usage)

Your LeisureMod Modern Dining Chair is designed for comfortable and stable seating in dining, kitchen, or living room environments.

• Intended Use: This chair is intended for indoor use as seating for one person.
• Floor Protection: The chair legs are equipped with plastic glides to protect your floors from scratches and scuffs. These glides also facilitate smooth and quiet movement across various surfaces.
• Stability: Always sit centrally on the seat. Avoid standing on the chair or using it as a step stool.

Image: The dining chair highlighting its protective floor glides and lightweight construction for easy movement.

Maintenance and Care

Proper care will extend the life and appearance of your chair.

• Cleaning: Wipe clean with a dry or damp cloth. For the leather upholstery, use a soft, damp cloth and mild soap if necessary, then wipe dry immediately. Avoid harsh chemicals or abrasive cleaners.
• Wood Finish: The stained poplar wood frame should be cleaned with a dry cloth. Avoid excessive moisture.
• Inspection: Periodically inspect all screws and connections. Tighten any loose hardware to maintain stability and safety.
• Sunlight Exposure: Avoid prolonged exposure to direct sunlight to prevent fading of the upholstery and wood finish.

Image: Close-up of the dining chair highlighting the leather upholstered seat and the stained wood finish of the frame.

Troubleshooting

If you encounter any issues with your chair, refer to the following common problems and solutions:

Specifications

Detailed specifications for the LeisureMod Modern Dining Chair (Model CDWN-18LBR).

• Model Name: Clivo
• Model Number: CDWN-18LBR
• Brand: LeisureMod
• Color: Walnut/Light Brown
• Material: Leather Upholstery, Poplar Wood Frame
• Product Dimensions: 20"D x 19.88"W x 30.9"H
• Seat Depth: 15 inches
• Item Weight: 10.58 pounds
• Weight Capacity: Up to 300 pounds
• Back Style: Open-Back Design, Solid Back
• Finish Type: Stained Finish (Walnut)
• Upholstery Thickness: Backrest 1.18", Seat 1.77"
• Foam Density: 1.5 lbs./cu. ft. (High-density foam)
• Leg Width: 0.98 inches
• Special Features: Protective Plastic Glides, X-shaped base under seat for stability.
• UPC: 644380735444

Image: Diagram showing the key dimensions of the dining chair: height (30.90"), depth (20"), and width (19.88").

Warranty Information

Specific warranty details for the LeisureMod Modern Dining Chair are not provided in this manual. For information regarding product warranty, please refer to the purchase documentation or contact LeisureMod customer support directly. Keep your proof of purchase for any warranty claims.

Support

For further assistance, questions, or to report missing/damaged parts, please contact LeisureMod customer support:

• Manufacturer: LeisureMod
• Online Store: Visit the LeisureMod Store on Amazon
• Please have your model number (CDWN-18LBR) and proof of purchase ready when contacting support.