Advanblack ProTek Machined Harley Crash Bar Sliders Instruction Manual

Introduction

The Advanblack ProTek Machined Harley Crash Bar Sliders are designed to provide robust protection for your motorcycle's engine and frame. These sliders are engineered for durability and offer a customizable aesthetic. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your crash bar sliders.

Image: A pair of black Advanblack ProTek Machined Harley Crash Bar Sliders.

What's in the Box

Upon unpacking, please verify that all components listed below are present and undamaged:

• Engine Guard Sliders (2 units)
• Screws Hardware (3/8-16 screws included)

Image: An exploded view showing the engine guard bars, sliders, and various screws and rubber components.

Specifications

Note: If the included screws do not fit your crash bar thread holes, use the original screws that came with your crash bar.

Setup and Installation

The Advanblack ProTek Crash Bar Sliders are designed for straightforward installation onto existing 1 1/4" crash bars or saddlebag guards with threaded holes. Follow these general steps for installation:

1. Identify Mounting Points: Locate the threaded holes on your motorcycle's 1 1/4" crash bars (front engine guard) or saddlebag guards (rear).
2. Prepare Sliders: Ensure the sliders are clean and free of debris.
3. Attach Sliders: Insert the provided 3/8-16 screws through the center of the sliders and thread them into the mounting points on your crash bars.
4. Secure Fasteners: Tighten the screws securely. Do not overtighten, as this may damage the threads or components. If the provided screws do not fit, use the original screws that came with your crash bar.
5. Verify Stability: After installation, gently check the sliders to ensure they are firmly attached and do not wobble.

For a visual guide, please refer to the installation videos below:

Visual Examples of Installed Sliders

Image: Front engine guard with sliders, including dimensional overview.

Image: Motorcycle showcasing installed front and rear sliders.

Operating Principles

The Advanblack ProTek Crash Bar Sliders function as a protective barrier for your motorcycle's engine and saddlebag guards. In the event of a tip-over or low-speed slide, these sliders are designed to absorb impact and reduce direct contact between the motorcycle's critical components and the ground. This helps to minimize potential damage to the frame, engine, and other expensive parts.

The rotatable end design allows the sliders to rotate upon impact, further dissipating energy and reducing friction, which can help prevent the motorcycle from catching and flipping during a slide. This feature contributes to enhanced safety and peace of mind while riding.

Image: Red CNC carbon inlay sliders providing protection on a motorcycle engine guard.

Maintenance

To ensure the continued effectiveness and appearance of your Advanblack ProTek Crash Bar Sliders, regular maintenance is recommended:

• Regular Cleaning: Clean the sliders periodically with a mild soap and water solution. Avoid harsh chemicals or abrasive cleaners that could damage the finish.
• Inspect for Damage: After any incident or periodically during routine checks, inspect the sliders for cracks, deep scratches, or deformation. Damaged sliders should be replaced immediately to maintain optimal protection.
• Check Fasteners: Ensure all mounting screws remain tight. Vibrations from riding can sometimes loosen fasteners over time. Re-tighten as necessary, but do not overtighten.
• Material Care: For Delrin sliders, ensure they are free from excessive dirt or grit that could cause premature wear. For CNC aluminum sliders, check for any signs of corrosion or fading.

Troubleshooting

If you encounter any issues with your crash bar sliders, consider the following:

• Loose Sliders: If a slider feels loose, re-tighten its mounting screw. If it continues to loosen, inspect the threads on both the screw and the crash bar for damage.
• Improper Fit: Ensure the sliders are correctly aligned with the threaded holes on your crash bar. If the provided screws do not fit, use the original screws from your crash bar.
• Visible Damage: If a slider shows significant damage (e.g., deep gouges, cracks) from an impact, it has served its purpose and should be replaced to ensure continued protection.
• Unusual Noise: If you hear rattling or other unusual noises coming from the sliders, check all mounting points and ensure they are securely fastened.

For further assistance, please contact Advanblack customer support.

Warranty and Support

Advanblack products are manufactured to high standards. For information regarding warranty coverage, terms, and conditions, please refer to the warranty documentation included with your purchase or visit the official Advanblack website.

For technical support, replacement parts, or any other inquiries, please contact Advanblack customer service through their official channels. Contact information can typically be found on the product packaging or the brand's website.

You can visit the Advanblack store for more information: Advanblack Store