OURPIC 9-Drawer Dresser and TV Stand

1. Introduction

Thank you for purchasing the OURPIC 9-Drawer Dresser and TV Stand. This versatile furniture piece is designed to provide ample storage and serve as a stable platform for your television. This manual provides detailed instructions for assembly, operation, maintenance, and troubleshooting to ensure safe and efficient use of your new dresser.

Image 1.1: The OURPIC 9-Drawer Dresser and TV Stand in a bedroom setting.

2. Safety Information

WARNING: Failure to follow these safety instructions could result in injury or property damage.

• Anti-Tipping Kit: For safety and stability, it is highly recommended to install the included anti-tipping kit. Secure the dresser to a wall using the provided hardware to prevent accidental tipping, especially in households with children.
• Weight Limits: Do not exceed the maximum weight capacity for the top surface or individual drawers. Refer to the 'Specifications' section for detailed weight limits.
• Assembly: Assemble the unit on a soft, clean surface to prevent scratches. Ensure all screws and fasteners are securely tightened before use. Do not overtighten.
• Placement: Place the dresser on a level surface. Uneven surfaces can compromise stability.
• Children: Do not allow children to climb on or play with the dresser or drawers. Keep small parts away from children during assembly.
• Moving: When moving the dresser, empty all drawers and lift the unit. Do not drag the dresser, as this may damage the frame or floor.

3. Package Contents

Before beginning assembly, verify that all parts listed below are present. If any parts are missing or damaged, please contact customer support.

4. Assembly Instructions

Follow these steps carefully to assemble your dresser. It is recommended to have two people for assembly.

1. Step 1: Assemble Lower Frames
   Connect frame 8 (long lower horizontal frame) and frame 7 (short lower horizontal frame) using two connector plates (12) and four screws C. Ensure the frames are aligned correctly.
2. Step 2: Attach Vertical Frames
   Install two vertical frames (4) onto the assembled lower frame (from Step 1) using two screws A.
3. Step 3: Insert Drawer Support Bars (Part 1)
   Insert one end of the drawer support bars (10) into the designated holes on the vertical frames (4).
4. Step 4: Secure Vertical Frames
   Insert the other end of the drawer support bars (10) into the holes on the vertical frames (4). Secure the vertical frames (4) to the lower frame (8) using two screws A.
5. Step 5: Assemble Upper Frames
   Connect two upper horizontal frames (6) and two upper horizontal frames (5) using two connector plates (12) and four screws C.
6. Step 6: Install Upper Frames
   Install the assembled upper frames (from Step 5) onto the vertical frames (4) using four screws A.
7. Step 7: Attach Left Side Board
   Insert one end of the remaining drawer support bars (10) into the holes on the vertical frames (4). Insert the other end into the holes on the left side board (2). Secure the left side board (2) with four screws C.
8. Step 8: Attach Right Side Board
   Insert one end of the remaining drawer support bars (10) into the holes on the vertical frames (4). Insert the other end into the holes on the right side board (3). Secure the right side board (3) with four screws C.
9. Step 9: Install X Steel Bar
   Install the X steel bar (9) on the back of the dresser frame using four screws C. This enhances stability.
10. Step 10: Connect Top Boards
    Insert two screws H and six wooden dowels F into the two top boards (1) to connect them together. Secure them with four screws E. Screw four nails D into the top board (1) as indicated.
11. Step 11: Install Top Board
    Carefully place the assembled top board (1) onto the main frame. Secure it to the frame using four screws E and twelve screws C.
12. Step 12: Assemble and Install Fabric Drawers
    Assemble the nine fabric drawers (11) by unfolding them and inserting the bottom panel. Attach the drawer handrails (G) to the front of each fabric drawer. Insert the assembled drawers into the frame.
13. Step 13: Install Anti-Tipping Kit
    For enhanced safety, install the anti-tipping kit (I) to secure the dresser to a wall. Follow the specific instructions provided with the anti-tipping kit.

Image 4.2: Detail of the wide thickened tabletop and wood side board.

5. Operating Instructions

5.1 Using the Drawers

• To open a drawer, gently pull the handrail (G) outwards.
• To close a drawer, push it back into the compartment until it is fully seated.
• Avoid overloading drawers to ensure smooth operation and prevent damage.

Image 5.1: The dresser with drawers open, demonstrating large storage capacity.

5.2 Using as a TV Stand

• The sturdy wood top is designed to support TVs up to 75 inches.
• Ensure the TV's base fits entirely within the top surface of the dresser.
• Distribute the weight of the TV evenly on the top surface.

Image 5.2: The dresser functioning as a TV stand.

6. Maintenance

6.1 Cleaning

• Wood Top: Wipe the wood top with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners that may damage the finish. Dry immediately with a clean cloth.
• Fabric Drawers: Spot clean fabric drawers with a mild detergent and a damp cloth. Allow to air dry completely. Do not machine wash or tumble dry.
• Metal Frame: Wipe the metal frame with a soft, dry cloth.

Image 6.1: Key features including waterproof tabletop and sturdy construction.

6.2 General Care

• Regularly check all screws and fasteners to ensure they remain tight. Retighten as necessary.
• Avoid exposing the dresser to direct sunlight or extreme temperature changes, which can cause warping or fading.
• Do not place hot items directly on the wood top without protection.

7. Troubleshooting

8. Specifications

Image 8.1: Product dimensions diagram.

9. Warranty & Support

For warranty information, missing parts, or any product-related inquiries, please contact OURPIC customer support directly. Refer to your purchase documentation or the OURPIC official website for contact details.

Please have your model number (DS-021-9D-63) and purchase date ready when contacting support.