Vizgifin Trail Camera User Manual

Introduction

Thank you for choosing the Vizgifin BST883C 4G LTE Cellular Trail Camera. This advanced game camera is designed for reliable outdoor monitoring, capturing high-resolution photos and videos of wildlife with real-time notifications. Its robust, waterproof design ensures performance in various environmental conditions. This manual provides detailed instructions for setting up, operating, and maintaining your camera to ensure optimal performance.

What's in the Box

• 1 x Vizgifin BST883C Trail Camera
• 1 x Built-in SIM Card
• 1 x 32GB Memory Card
• 1 x Metal Bracket (for wall mounting)
• 1 x Mounting Strap (for tree mounting)
• 1 x Data Cable (USB-C to USB)
• 1 x User Manual

Figure 1: Vizgifin BST883C Trail Camera and included accessories.

Product Overview

Key Features:

• 4G LTE Cellular Connectivity: Supports Verizon, T-Mobile, and AT&T networks for real-time data transmission without Wi-Fi.
• High-Resolution Imaging: Captures 60MP still images and stunning 4K HD videos.
• Fast Motion Detection: 0.1-second trigger speed with a 120° PIR detection angle, covering up to 85 feet.
• Clear Night Vision: Equipped with 32 850nm infrared LEDs for bright, low-noise black and white images up to 85 feet in complete darkness.
• IP67 Waterproof Rating: Designed to withstand rain, snow, and dust, operating in temperatures from -22°F to 158°F.
• "TrailCam Go" Mobile App: Allows for real-time notifications, remote settings adjustment, camera angle check, and content sharing.
• Built-in SIM Card & 32GB SD Card: Ready for immediate use with included storage and trial data plan.

Figure 2: 4G LTE Cellular & APP Control for remote monitoring.

Figure 3: High-resolution 60MP images and 4K video capabilities.

Figure 4: Fast 0.1-second trigger speed for capturing quick movements.

Figure 5: Real-time alerts delivered to your smartphone.

Figure 6: 120° wide-angle detection for broader coverage.

Figure 7: IP67 Waterproof rating for all-weather durability.

Setup

1. Power Installation (Batteries or Solar Panel)

The camera can be powered by 12 AA batteries (not included) or an external 12V solar panel (not included). To install batteries, unlatch the camera and open the casing. Insert 12 AA batteries into the designated slots, ensuring correct polarity. For solar panel use, connect the 12V solar panel to the DC port located on the bottom of the camera, covered by a rubber cap. This port is designed to keep the camera charged and running continuously.

2. SD Card Installation

A 32GB SD card is pre-installed in the camera. If you need to remove or replace it, gently push the SD card into its slot until it clicks, then release to eject. Insert the new SD card with the gold contacts facing down until it clicks into place.

3. SIM Card & Cellular Setup

The camera comes with a built-in SIM card that supports Verizon, T-Mobile, and AT&T networks in the United States. Upon first use, a trial data package of 1,000 photos/videos is provided. To manage cellular data and receive real-time notifications, download the "TrailCam Go" mobile app from your smartphone's app store. Follow the in-app instructions to bind your camera and activate your data plan. Additional data packages (Standard, Premium, Unlimited) can be purchased through the app after the trial period.

4. Antenna Attachment

Screw the provided antenna firmly into the antenna port located on the top of the camera. Ensure it is securely attached for optimal signal reception.

5. Mounting the Camera

The camera offers two mounting options:

• Tree Mounting (using Mounting Strap): Thread the provided mounting strap through the slots on the back of the camera. Wrap the strap around a tree or pole at the desired height and secure it tightly using the buckle. The camera's back features spikes to enhance grip on tree bark, preventing slippage.
• Wall Mounting (using Metal Bracket): Attach the metal bracket to a wall or flat surface using the included screws and drywall anchors. Once the bracket is secure, screw the camera onto the bracket's adjustable head. The adjustable knob on the bracket allows for precise positioning and tension adjustment of the camera.

Operating Instructions

1. Powering On and Initializing

After installing batteries/connecting power and the SD card, slide the power switch from "OFF" to "SETUP". The camera's 2.4-inch LCD screen will power on and begin initializing. This mode allows you to access the camera's settings and preview the camera's view.

2. Navigating the Menu

Use the control buttons (MENU, OK, UP, DOWN, LEFT, RIGHT) to navigate through the settings menu on the LCD screen. Key settings include:

• Cellular Info: View details about your cellular connection.
• Bind APP: Instructions for connecting to the "TrailCam Go" app.
• Mode: Select between Photo, Video, or Photo + Video mode.
• Work Time: Set specific operating hours for the camera.
• Photo Resolution: Choose image quality (2MP, 4MP, 8MP, 16MP, 20MP, 60MP). Note: Cellular transmission may be limited to lower resolutions (2MP, 4MP, 8MP).
• Video Resolution: Select video quality (720P, 1080P, 2.7K, 4K).
• Photo Burst: Set the number of photos taken per trigger (e.g., 1P, 2P, 3P).
• Audio Recording: Enable or disable audio capture for videos.
• PIR Sensitivity: Adjust the sensitivity of the motion sensor (High, Medium, Low).

3. Activating Monitoring Mode

Once all settings are configured, slide the power switch from "SETUP" to "ON". The camera will enter monitoring mode, indicated by the screen turning off. The camera is now ready to detect motion and capture images/videos according to your settings.

4. Using the "TrailCam Go" App

The "TrailCam Go" app is essential for remote management. After binding your camera, you can:

• Receive real-time notifications when motion is detected.
• View captured photos and videos directly on your phone.
• Adjust camera settings remotely.
• Check the camera's battery level and signal strength.
• Share content to social media.

Maintenance

• Battery Replacement: Regularly check battery levels via the app or on the camera's screen. Replace all 12 AA batteries simultaneously to ensure consistent power.
• SD Card Management: Periodically check the remaining storage space on the 32GB SD card. Transfer important files to a computer and format the SD card to maintain optimal performance and prevent data corruption.
• Cleaning: Gently wipe the camera lens and PIR sensors with a soft, lint-free cloth to remove dirt, dust, or smudges. Do not use abrasive cleaners.
• Waterproofing Check: Ensure the rubber seal around the camera casing is clean and free of debris before closing the latch. This maintains the IP67 waterproof rating.
• Firmware Updates: Check the "TrailCam Go" app or the manufacturer's website for any available firmware updates to improve camera performance and add new features.

Troubleshooting

• Camera Not Powering On: Check battery installation and ensure they are fresh. If using a solar panel, verify the connection and sunlight exposure.
• No Photos/Videos Captured: Ensure the camera is in "ON" mode. Check PIR sensitivity settings. Verify SD card is inserted correctly and has sufficient space.
• Poor Image/Video Quality: Check selected resolution settings. Clean the camera lens. Ensure adequate lighting for night vision (within 85ft range).
• No Cellular Connection/Notifications: Verify SIM card is active and data plan is sufficient. Check cellular signal strength in the camera's location via the app. Ensure the antenna is securely attached.
• App Connectivity Issues: Ensure your smartphone has a stable internet connection. Restart both the camera and the app. Re-bind the camera if necessary.
• Excessive Battery Drain: This camera requires 12 AA batteries. Consider using a 12V solar panel for continuous power. Adjust settings like video length, photo burst, and PIR sensitivity to reduce power consumption.

Specifications

Warranty and Support

For warranty information, technical support, or any inquiries regarding your Vizgifin Trail Camera, please refer to the contact details provided in the packaging or visit the official Vizgifin website. Keep your purchase receipt as proof of purchase for warranty claims.