Introduction
The Onemake Soft Close Motion Damper Mechanism is designed to enhance the functionality of your cabinet doors by providing a smooth, quiet closing action. This device retrofits existing full overlay hinges, eliminating slamming and reducing wear on cabinets and hinges. This manual provides essential information for proper installation, operation, and maintenance of your soft close dampers.
Product Overview
The Onemake Soft Close Damper is a compact, clip-on accessory made from durable iron and plastic. It integrates seamlessly with compatible cabinet hinges to provide a controlled closing motion. The internal mechanism features a spring and dampening system that absorbs the closing force, ensuring a gentle and silent closure.
Image: The Onemake Soft Close Motion Damper Mechanism, a compact device designed for cabinet hinges.
Image: An internal view of the soft close damper, illustrating its solid construction and the smooth dampening system with uncompressed and compressed spring states.
Compatibility
This soft close damper is designed for use with Full Overlay Hinges, specifically those with a straight arm. It is crucial to verify the dimensions of your hinge's opening for proper fitment.
- Opening Length: Must be between 8mm and 9.5mm (0.3 inches to 0.37 inches). An opening exceeding 9.5mm may result in a loose fit.
- Opening Width: Must be at least 7.6mm (0.29 inches) for successful installation.
- Incompatible Hinge Types: Half Overlay Hinges and Inset Hinges are not compatible with this damper.
Image: A visual guide detailing compatible hinge types (Straight Arm Full Overlay Hinge) and the specific dimensional requirements for the hinge opening (length 8mm-9.5mm, width min 7.6mm).
Installation Guide
The Onemake Soft Close Damper features a clip-on design for quick and easy installation without the need for tools or screws.
Clip-on Attachment
- Identify the appropriate opening on your full overlay hinge where the damper will attach.
- Align the damper with the hinge opening.
- Gently push the damper into position until it snaps securely onto the hinge. No screws or additional adjustments are required.
Effortless Removal
- Locate the tail end of the damper.
- Press the tail of the damper gently towards the hinge.
- While pressing, lift the damper upward to detach it from the hinge.
Image: Step-by-step visual instructions for both clipping the damper onto the hinge and detaching it, highlighting the simplicity of the process.
Operation
Once installed, the soft close damper automatically engages as the cabinet door approaches its closed position. The integrated dampening system slows the door's movement, preventing it from slamming shut. This results in a quiet and controlled closure, protecting both the cabinet and its contents.
Image: A visual comparison demonstrating the difference between a cabinet door equipped with a soft close damper (closing quietly) and one without (slamming shut), along with an illustration of easy clip-top installation.
Image: The soft close damper discreetly installed on a cabinet hinge, demonstrating its integration into a typical kitchen cabinet setup.
Maintenance
The Onemake Soft Close Damper is designed for minimal maintenance. Periodically, you may:
- Cleaning: Wipe the exterior of the damper with a soft, dry cloth to remove dust or debris. Avoid using harsh chemicals or abrasive cleaners.
- Inspection: Occasionally check that the damper remains securely clipped onto the hinge. If it appears loose, re-clip it firmly.
Troubleshooting
If you encounter issues with your soft close damper, consider the following:
- Damper is loose or falls off:
Solution: Ensure the hinge opening length is within the specified range of 8mm to 9.5mm (0.3 inches to 0.37 inches). If the opening is too wide, the damper may not secure properly. Re-clip the damper firmly. - Cabinet door still slams:
Solution: Verify that the damper is correctly installed and fully clipped onto the hinge. Check if the hinge itself is a compatible full overlay straight-arm type. Ensure the damper is not obstructed by any part of the cabinet or door. For larger or heavier doors, multiple dampers may be required. - Damper does not fit:
Solution: Confirm that your hinge is a full overlay straight-arm type and that its opening dimensions meet the minimum width of 7.6mm (0.29 inches) and the length range of 8mm-9.5mm (0.3 inches-0.37 inches).
Product Specifications
| Feature | Detail |
|---|---|
| Brand | Onemake |
| Model Number | ZN01 |
| Material | Iron, Plastic |
| Color | Nickel |
| Style | Clip Top |
| Mounting Type | Clip On |
| Item Package Quantity | 10 |
| Item Weight | 12.6 ounces (for 10-pack) |
| Size | 3.02"L x 0.7"W |
| Compatibility | Full Overlay Hinges (Straight-Arm) with specific opening dimensions |
Warranty and Support
For specific warranty information or technical support regarding your Onemake Soft Close Motion Damper Mechanism, please refer to the product packaging or contact Onemake customer service directly. Keep your purchase receipt for warranty claims.