NEEWER Z2PRO-N TTL Round Head Flash Speedlite for Nikon User Manual

1. Introduction

This manual provides comprehensive instructions for the NEEWER Z2PRO-N 2.4G TTL Round Head Flash Speedlite. It covers product features, setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your device. Please read this manual thoroughly before using the flash speedlite.

Package Contents

• 1 x Speedlite Flash
• 1 x Protective Case
• 1 x Mini Stand
• 1 x Lithium Battery (7.2V/3000mAh)
• 1 x USB Cable (Type-C)

2. Product Overview

The NEEWER Z2PRO-N is a high-performance 2.4G TTL round head flash speedlite designed for Nikon cameras. It features a robust 76Ws output, an efficient cooling system, and an upgraded user interface for enhanced usability.

Key Features

• 76Ws Output: Provides powerful and consistent illumination.
• Efficient Cooling System: Supports up to 100 continuous full power flashes without overheating.
• Upgraded Quartz Tube: Designed for durability, supporting up to 100,000 flashes.
• Flexible Flash Head: Swivels 330° and tilts -7° to 120° for versatile light bouncing.
• Dual 2W 3300K LED Modeling Lamps: Offers 10 brightness levels for pre-visualization.
• Upgraded UI and TCM Key: Allows instant switching between i-TTL and Manual modes.
• Comprehensive Flash Modes: Includes i-TTL automatic metering, 1/1-1/256 manual dimming, stroboscopic flashes, 1/8000s HSS, front/rear curtain sync, FEC/FEB/FEL, and S1/S2 optical slave modes.
• Expanded 2.4G Wireless System: Compatible with NEEWER QPRO-N TTL transmitters (not included) for master/slave operation (4 groups, 32 channels, 99 IDs, up to 100m range). Also compatible with Godox 2.4G X system (RX COMPAT menu) and Sekonic L-858D light meter (RT-GX module).
• High Capacity Lithium Battery: 7.2V/3000mAh battery provides 600 full power flashes with a 1.5s recycling time.
• USB Type-C Charging: Battery can be charged via a Type-C port in approximately 2.5 hours using a 5V 2A USB charger (not included).
• Firmware Updates: Available via the USB Type-C port.

This image displays the main components of the NEEWER Z2PRO-N package, including the flash unit, its rechargeable lithium battery, a USB Type-C charging cable, and a protective pouch.

3. Setup

3.1 Charging the Battery

1. Insert the 7.2V/3000mAh lithium battery into the designated battery compartment of the flash unit.
2. Connect the provided USB Type-C cable to the battery's Type-C port.
3. Connect the other end of the USB cable to a 5V 2A USB charger (not included).
4. The battery will fully charge in approximately 2.5 hours.

This image illustrates the USB Type-C charging port located on the side of the lithium battery, allowing for convenient direct charging.

3.2 Mounting the Flash on Camera

1. Ensure your Nikon camera is powered off.
2. Slide the metal hot shoe of the Z2PRO-N flash into the camera's hot shoe mount.
3. Engage the quick lock mechanism to secure the flash firmly in place.
4. The flash is compatible with various Nikon DSLR and mirrorless cameras (e.g., Z9, Z8, Zfc, Z50, Z30, Z5, Z6, Z7, Z6II, Z7II, D4, D5, D6, D60, D70S, D90, D100, D200, D300, D610, D700, D750, D780, D800, D850, D3100, D3200, D3300, D3400, D3500, D5000, D5100, D5200, D5300, D7100, D7500). Note: Not compatible with D810.

This image demonstrates the NEEWER Z2PRO-N flash attached to a Nikon camera, highlighting the quick lock and metal hot shoe design for secure mounting.

4. Operating Instructions

4.1 Power On/Off

Press and hold the power button to turn the flash speedlite on or off. The display will illuminate upon power-on.

4.2 Navigating the User Interface

The Z2PRO-N features an upgraded UI for intuitive control. Use the control dial and buttons to navigate through menus and adjust settings.

This image provides a detailed look at the flash's control panel, including the display screen and various buttons for mode selection and parameter adjustment.

4.3 Flash Modes

• i-TTL Automatic Flash: The flash automatically determines the correct exposure.
• Manual (M) Flash: Allows manual adjustment of flash output from 1/1 to 1/256.
• TCM Conversion: Press the dedicated TCM key to instantly switch between i-TTL and Manual modes.
• Multi Strobe Flash: Fires a series of rapid flashes during a single exposure.
• S1/S2 Optical Slave Modes: Triggers the flash wirelessly by detecting another flash.

4.4 High-Speed Sync (HSS)

The Z2PRO-N supports 1/8000s High-Speed Sync, enabling you to use flash at shutter speeds faster than your camera's native sync speed. This is useful for overpowering ambient light outdoors or using wider apertures.

This image visually compares a photograph taken with HSS to one without, illustrating how HSS helps balance flash exposure with bright backgrounds, such as a sunny beach scene.

4.5 Wireless Operation (2.4G System)

The Z2PRO-N integrates a 2.4G wireless system for remote control and multi-flash setups.

• NEEWER Q System: Can act as a master or slave unit with NEEWER QPRO-N TTL transmitters (not included) and other Q system flashes (e.g., Q200, Q4, S102 Pro, QR Receiver, Z1, Z2, Z880, NW760). Supports 4 groups (M/A/B/C), 32 channels (CH1-CH32), and 99 IDs (1-99, OFF) with a transmission distance up to 100m (328ft).
• Godox X System Compatibility: Can function as a slave unit with Godox 2.4G X system transmitters (e.g., Xpro, X3, X2) by enabling the "RX COMPAT" menu option.
• Sekonic L-858D Compatibility: Compatible with Sekonic L-858D light meter (RT-GX module).
• Important Note: NEEWER Q and Godox X systems cannot be used simultaneously. Ensure the latest firmware is installed for full compatibility.

This diagram shows the NEEWER QPRO transmitter controlling the Z2PRO flash, alongside other compatible NEEWER Q system flashes. It also depicts the Z2PRO's compatibility as a slave unit with Godox 2.4G X system and Sekonic L-858D light meters.

4.6 Adjusting the Flash Head

The flash head offers significant flexibility for bouncing light.

• Rotation: The flash head can rotate 0-330° horizontally.
• Tilt: The flash head can tilt from -7° to 120° vertically.

This image visually explains the range of motion for the flash head, demonstrating its ability to tilt vertically from -7 to 120 degrees and rotate horizontally up to 330 degrees for flexible light positioning.

4.7 Modeling Lamps

The two 2W 3300K LED modeling lamps provide continuous light for pre-visualizing lighting effects. They offer 10 adjustable brightness levels (01-10).

5. Maintenance

• Cleaning: Use a soft, dry cloth to clean the flash unit. Avoid using harsh chemicals or abrasive materials.
• Storage: Store the flash in a cool, dry place, away from direct sunlight and extreme temperatures. Use the provided protective case for storage and transport.
• Battery Care: For long-term storage, charge the lithium battery to approximately 50% and recharge every 3-6 months to maintain battery health.
• Firmware Updates: Regularly check the NEEWER official website for available firmware updates to ensure optimal performance and compatibility. Updates can be installed via the USB Type-C port.

6. Troubleshooting

7. Specifications

8. Warranty and Support

For warranty information and technical support, please refer to the official NEEWER website or contact their customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.

Manufacturer: NEEWER

Website: www.neewer.com