1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Sunmerit Universal Ceiling Fan Remote Control Switch Kit. This kit is designed to provide convenient control over your ceiling fan's speed and light functions, including dimming, from both a wall-mounted switch and a handheld remote. It features an upgraded 3-wire connection for simplified installation.
2. Safety Information
- Always turn off power at the circuit breaker before beginning installation or performing any maintenance.
- Installation should be performed by a qualified electrician if you are not comfortable with electrical wiring.
- Ensure all wiring connections are secure and properly insulated.
- This device is for indoor use only.
- Do not exceed the maximum load ratings for the fan and light.
3. What's in the Box
- 1 x Receiver
- 1 x Wall Switch
- 1 x Remote Control (requires 9V battery, not included)
4. Setup and Installation
4.1 Wiring Diagram
This upgraded kit requires only 3 wires from the wall switch to control the ceiling fan and lights (AC Load IN, AC Load OUT, and Ground line). Refer to the diagram below for proper wiring connections.
Figure 1: Wiring Diagram for Receiver and Wall Switch
4.2 DIP Switch Setting
To ensure proper communication between the remote, wall switch, and receiver, the DIP switch settings on all three components must match. The kit offers 16 different code frequencies to prevent interference with other devices. The factory setting is typically all 'up' (ON), but you can adjust these as needed.
Figure 2: DIP Switch Locations and Settings
4.3 Compatibility
This kit is compatible with most downrod style AC fans. It is not recommended for use with hugger style fans, wall-mounted fans, or exhaust-type fans. It supports incandescent light bulbs and some dimmable LED lamps. Other LED lamps and CFL lamps may only support ON/OFF functionality without dimming. This fan light switch does NOT support Wi-Fi.
Figure 3: Fan and Bulb Compatibility Overview
4.4 Installation Video
Watch this video for a visual guide on the installation process and product overview.
Video 1: Overview of the Sunmerit Ceiling Fan Remote and Dimmer Combo Kit, including components and basic wiring concepts.
5. Operating Instructions
5.1 Wall Switch Control
The wall switch provides direct control over your fan and light. It features buttons for fan ON/OFF, fan speed adjustment (+/-), and light ON/OFF/Dimming. Indicator lights show the current fan speed setting.
Figure 4: Wall Switch in Use
5.2 Remote Control
The handheld remote offers convenient control from anywhere in the room. It includes buttons for Low, Medium, High fan speeds, Fan OFF, Light ON/OFF, and a timer function (1H, 2H, 4H, 8H).
Figure 5: Remote Control Functions
5.3 Functionality Video
This video demonstrates the various functions of the Sunmerit Ceiling Fan Switch Combo.
Video 2: Demonstration of fan speed control, light ON/OFF, and dimming features using the wall switch and remote.
6. Maintenance
- Cleaning: Wipe the remote and wall switch with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: The remote control requires a 9V battery. Replace the battery when the remote's range decreases or it stops responding.
- Regular Checks: Periodically check all wiring connections for tightness and signs of wear.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan or Light not responding | No power to the unit; DIP switches not matched; Remote battery low/dead. | Check circuit breaker; Ensure DIP switches on remote, wall switch, and receiver match; Replace remote battery. |
| Interference with other fans | DIP switch code is the same as another nearby fan. | Change the DIP switch settings on the affected units to a unique combination. |
| Light does not dim | Incompatible light bulb (non-dimmable LED or CFL). | Ensure you are using incandescent or dimmable LED bulbs. |
| Fan speed seems lower than expected | Fan's internal settings or motor type. | Ensure the fan's pull chain (if any) is set to its highest speed before using the remote/wall switch. This kit is designed for AC motors. |
8. Specifications
| Feature | Specification |
|---|---|
| Operation Mode | ON-OFF |
| Current Rating | 1 Amps |
| Operating Voltage | 120 Volts |
| Contact Type | Normally Open |
| Connector Type | Crimp |
| Terminal | Screw |
| Item Dimensions (L x W x H) | 6.42 x 6.42 x 2.36 inches |
| Circuit Type | 1-way |
| Contact Material | Brass |
| International Protection Rating | IP44 |
| Number of Positions | 1 |
| Upper Temperature Rating | 40 Degrees Celsius |
| Controller Type | Push Button |
| Control Method | Remote |
| Unit Count | 3.0 Count |
| Number of Items | 3 |
| Item Weight | 13.7 ounces |
| Material | Brass |
9. Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact Sunmerit customer service directly. Keep your purchase receipt for any warranty claims.