Introduction
This instruction manual provides comprehensive guidance for the installation, operation, and maintenance of your CREA Infrared Sensor Kitchen Faucet, Model 109368. This advanced kitchen faucet features automatic touchless operation, a versatile pull-out sprayer with three distinct water flow modes, and a durable chrome finish. Please read this manual thoroughly before installation and use to ensure proper function and longevity of your product.
Image: The CREA Infrared Sensor Kitchen Faucet, showcasing its sleek chrome finish and pull-out sprayer design.
Safety Information
- Always turn off the main water supply before beginning any installation or maintenance.
- Ensure all connections are secure to prevent leaks.
- Do not use abrasive cleaners or harsh chemicals on the faucet's finish, as this may damage the chrome.
- The sensor requires 4 AA batteries. Ensure correct polarity when inserting batteries. Do not mix old and new batteries or different types of batteries.
- Keep the sensor area clean and unobstructed for optimal performance.
- If you are unsure about any installation steps, consult a qualified plumber.
Package Contents
Please verify that all components are present before starting installation:
- CREA Kitchen Faucet (Main Body)
- Pull-Out Sprayer Head
- Mounting Hardware (nuts, washers, gaskets)
- Hot and Cold Water Supply Lines
- Sensor Control Box
- Battery Box (requires 4 AA batteries, not included)
- Counterweight for Pull-Out Hose
- Instruction Manual (this document)
- Adapters (e.g., 3/8 to 1/4 inch for hoses, if applicable)
Setup and Installation
The CREA Kitchen Faucet is designed for single-hole deck mounting. Follow these steps for proper installation:
- Prepare the Sink: Ensure the mounting hole on your sink or countertop is clean and clear.
- Mount the Faucet: Insert the faucet body into the mounting hole. From underneath the sink, secure it with the provided washer and mounting nut. Tighten firmly but do not overtighten.
- Connect Water Supply Lines: Attach the hot and cold water supply lines to the corresponding connections on the faucet body. Connect the other ends to your hot and cold water supply valves. Ensure all connections are watertight.
- Install Sensor Control Box: Connect the sensor cable from the faucet to the sensor control box. Mount the control box in an accessible location under the sink.
- Install Battery Box: Insert 4 AA batteries (not included) into the battery box, observing polarity. Connect the battery box cable to the sensor control box.
- Install Pull-Out Hose and Counterweight: Feed the pull-out sprayer hose through the faucet spout. Connect the hose to the water outlet on the sensor control box. Attach the counterweight to the pull-out hose at a suitable height to ensure smooth retraction.
- Test for Leaks: Turn on the main water supply and check all connections for leaks.
Image: Diagram illustrating the faucet dimensions (height 448mm/17.6", spout reach 217mm/8.5", base diameter 55mm/2.2") and the under-sink connections for water lines, sensor control box, and battery box.
Operating Instructions
Manual Operation
The single handle on the side of the faucet controls both water flow and temperature:
- Water Flow: Lift the handle to turn on the water. The further you lift, the greater the flow. Push down to turn off.
- Temperature Control: Move the handle left for hot water and right for cold water.
Image: Close-up of the single handle, indicating its function for adjusting water volume and temperature. Red dot for hot, blue dot for cold.
Infrared Sensor Operation (Touchless)
For hands-free convenience, the faucet features an infrared motion sensor:
- Activation: Wave your hand within 10 cm (approximately 4 inches) of the sensor located at the base of the faucet. The water will turn on within 0.5 seconds.
- Deactivation: Wave your hand in front of the sensor again to turn off the water.
- Automatic Shut-off: To conserve water, the faucet will automatically turn off after 3 minutes of continuous flow if no further motion is detected.
- Low Battery Indicator: The sensor control box will provide an indication when the batteries are low, reminding you to replace them.
Image: Illustration demonstrating the infrared sensor's detection zone and hands-free activation.
Pull-Out Sprayer and Water Flow Modes
The pull-out sprayer offers enhanced flexibility and three distinct water flow modes:
- Pull-Out Function: Grasp the sprayer head and pull it out from the spout. The hose extends up to 60 cm (approximately 23.6 inches), providing extensive reach for cleaning the sink or filling pots. The faucet also features a 360° swivel for full sink access.
- Mode Selection: Use the button(s) on the sprayer head to switch between the three modes:
- Spray Mode: A wide, powerful spray for rinsing dishes and cleaning.
- Stream Mode: A steady, aerated flow for everyday tasks like filling glasses or pots.
- Sweep Mode: A strong, blade-like water flow for stubborn food residue.
- Retraction: When finished, gently guide the sprayer head back into the spout. The counterweight will assist in smooth retraction.
Image: The pull-out sprayer extended, showing its 60cm reach and the faucet's 360-degree swivel capability for comprehensive sink coverage.
Image: Visual representation of the three distinct water flow modes: Spray, Stream, and Sweep, available from the pull-out sprayer.
Maintenance
- Cleaning the Faucet: To maintain the chrome finish, clean regularly with a soft cloth and mild soap or a non-abrasive cleaner specifically designed for chrome. Rinse thoroughly and dry immediately to prevent water spots.
- Cleaning the Sprayer Nozzles: If water flow becomes irregular, the sprayer nozzles may be clogged. Gently rub the rubber nozzles to dislodge mineral deposits. For more stubborn clogs, unscrew the sprayer head and soak it in a vinegar solution.
- Battery Replacement: When the low battery indicator activates, replace the 4 AA batteries in the battery box. Ensure the faucet is off before replacing batteries.
- Sensor Maintenance: Keep the infrared sensor window clean and free from obstructions to ensure reliable touchless operation.
Image: Cutaway view highlighting the premium ceramic cartridge, tested for 500,000 on/off cycles, ensuring durability and leak-free performance.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No water flow (sensor mode) | Low or dead batteries; sensor obstructed; water supply off. | Replace batteries; clear sensor area; check water supply valves. |
| Sensor not responding | Sensor window dirty; insufficient light; object too far/close. | Clean sensor window; ensure adequate lighting; wave hand within 10 cm. |
| Weak water pressure | Clogged aerator/nozzles; partially closed water supply valve. | Clean sprayer nozzles; fully open water supply valves. |
| Leaks from connections | Loose connections; damaged washers. | Tighten connections; replace washers if damaged. |
| Sprayer does not retract smoothly | Counterweight improperly positioned; hose obstructed. | Adjust counterweight position; clear any obstructions around the hose. |
Specifications
- Model Number: 109368
- Brand: CREA
- Material: 304 Stainless Steel
- Finish: Chrome
- Style: Infrared Sensor
- Installation Method: Single-hole (Monotrou)
- Number of Handles: 1
- Special Features: Pull-out sprayer, 3 water modes (Spray, Stream, Sweep), Touchless sensor operation, Low battery indicator
- Sensor Response Time: 0.5 seconds
- Sensor Detection Zone: 10 cm
- Automatic Shut-off: 3 minutes
- Power Source: 4 AA Batteries (not included)
- Product Dimensions (L x W x H): 44 x 33.2 x 7.6 cm (17.3 x 13.1 x 3 inches)
- Item Weight: 2.67 Kilograms (5.89 lbs)
- Country of Origin: China
Warranty and Support
Warranty information for your CREA faucet is typically included with the product packaging or can be found on the official CREA website. Please retain your proof of purchase for warranty claims.
For technical support, troubleshooting assistance, or to inquire about replacement parts, please refer to the contact information provided in your product packaging or visit the official CREA website.
Note: Availability of spare parts information is currently unavailable through this document.