Introduction
This manual provides essential information for the safe and efficient operation, assembly, and maintenance of your SISIGAD Electric Bike. Please read this manual thoroughly before first use and retain it for future reference.
Figure 1: SISIGAD Electric Bike, 1200w-26x4"fat Tire Ferrous Gray model.
Safety Information
Always prioritize safety when operating the electric bike. Adhere to all local traffic laws and regulations. Wearing a helmet and appropriate safety gear is strongly recommended.
- Ensure all components are securely fastened before each ride.
- Regularly check tire pressure, brakes, and battery charge.
- Do not operate the bike under the influence of alcohol or drugs.
- Be aware of your surroundings and potential hazards.
- Avoid riding in extreme weather conditions.
Package Contents
Upon unpacking, verify that all components listed below are present and undamaged:
- SISIGAD Electric Bike Frame (partially assembled)
- Front Wheel
- Front Fender
- Pedals (Left and Right)
- Saddle
- Tool Kit (including hex wrenches and open-end wrenches)
- Power Adapter
- User Manual
- Front Quick Release Skewer
- Transmission Protection Driver
Setup and Assembly
The electric bike arrives approximately 80% pre-assembled. Follow these steps for final assembly:
1. Unpacking and Inspection
Carefully remove the bike and all accessories from the original packaging. Inspect for any damage during transit. It is recommended to take photos of the original packaging and all accessories upon receipt.
Video 1: Comprehensive installation guide for the electric bike, covering all assembly steps.
2. Install Parking Rack
Use a 5mm hex wrench from the toolkit to remove the parking stand screws. Place the parking stand in the designated frame position and securely lock the screws.
3. Install the Front Wheel
Remove the nut from one side of the quick-release axle. Pass the quick-release axle through the front wheel hub. Place the tapered spring end safety hook on the other side and lock the nut in place. Use a 17mm open-end wrench to remove the front fork protective rod. Remove the orange brake protector. Lift the front fork and carefully place the front wheel, ensuring the disc rotor is aligned with the disc brake caliper. Hook the safety hook onto the front fork and tighten the load handle.
4. Install the Front Wheel Fender
Remove the fender screws from the front fork. Place the fender onto the frame. Install the front light onto the fender and lock the screws securely.
5. Installing the Handlebars
Adjust the handlebars to your preferred angle. Use a 5mm hexagonal screwdriver to unscrew the four screws on the handlebar clamp. Place the handlebars onto the stem, pre-install the four screws, but do not tighten them fully. Adjust the handlebar angle first, then tighten the screws. Ensure the front wheel is aligned with the frame in a straight line before fully tightening the torque tube screws.
6. Installing the Footboard (Pedals)
Identify the left (L) and right (R) pedals. The pedal marked 'L' is for the left side and tightens counter-clockwise using a 15mm open-end wrench. The pedal marked 'R' is for the right side and tightens clockwise. Ensure they are securely fastened.
7. Check All Functions
After assembly, perform a comprehensive check of all functions. This includes checking the transmission, index shifting, and front light operation. Ensure the battery is properly installed and charged.
Operating Instructions
Powering On/Off and Lights
To power on the bike, long press the power button on the display. To turn on the front light, press and hold the light button on the control panel.
Riding Modes and Pedal Assist
The SISIGAD Electric Bike offers multiple riding modes: pure electric mode, pedal assist mode, and classic bike mode. There are 5 pedal assist levels (PAS) to choose from. To activate the rear wheel drive in electric mode, press the shift button after selecting gear 1.
Figure 2: Illustration of the three riding modes available on the electric bike.
Smart APP Control
The electric bike can be controlled via a smart APP. Download "Orbital Sports" from your device's app store. Register an account and ensure your phone's Bluetooth is not connected to the e-bike before opening the app. Long press the power button on the bike to turn it on. In the app, connect to Bluetooth (look for TST-M612). Once connected, you can unlock Class 3 mode for increased speed (up to 25 MPH). Be aware of local regulations regarding Class 3 e-bikes.
Video 2: Demonstration of connecting the electric bike to the Orbital Sports app via Bluetooth and unlocking Class 3 mode.
The app allows you to monitor riding data and adjust settings. The maximum speed can reach 25 MPH through pedal assistance after unlocking Class 3 mode.
Push Mode (6 KM/H)
The bike features a 6 KM/H push mode, which provides a gentle assist for walking alongside the bike, making it easier to navigate pedestrian areas or push uphill.
Figure 3: The electric bike's push mode provides assistance for easy walking alongside the bike.
Maintenance
- Battery Care: The 48V/10AH removable waterproof battery can be fully charged in 5-6 hours. Store the battery in a cool, dry place and charge it regularly, even when not in use, to prolong its lifespan.
- Tire Pressure: Regularly check and maintain the recommended tire pressure for the 26"x4.0" fat tires to ensure optimal performance and safety.
- Brake System: Inspect the dual disc brakes periodically for wear and tear. Ensure the brake pads are not excessively worn and the brake levers operate smoothly.
- Cleaning: Clean the bike regularly with a damp cloth. Avoid using high-pressure water jets directly on electrical components.
- Lubrication: Lubricate the chain and other moving parts as needed to ensure smooth operation and prevent rust.
- General Inspection: Periodically check all bolts and fasteners for tightness.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Bike does not power on. | Low battery charge; Battery not properly installed; Loose electrical connection. | Charge the battery; Re-install the battery securely; Check all visible electrical connections. |
| Motor not assisting. | PAS level set to 0; Brake levers engaged; Motor connection issue. | Increase PAS level on display; Release brake levers; Check motor cable connection. |
| Brakes feel weak. | Worn brake pads; Loose brake cable; Air in hydraulic system (if applicable). | Inspect and replace brake pads; Adjust brake cable tension; Consult a professional for hydraulic brake bleeding. |
| Gears not shifting smoothly. | Derailleur misalignment; Dirty/dry chain; Damaged shift cable. | Adjust derailleur; Clean and lubricate chain; Inspect and replace shift cable if damaged. |
If you encounter problems not listed here or require further assistance, please contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Bike Type | Electric Bike |
| Motor | 1200W (Peak) Brushless Motor |
| Max Speed (Unlocked) | 25 mph (via pedal assistance) |
| Battery | 48V/10AH Removable Waterproof Battery |
| Max Travel Range | Up to 60 Miles |
| Charging Time | 5-6 hours |
| Tires | 26" x 4.0" Fat Tires |
| Gears | 7-Speed Gearbox |
| Brakes | Dual Disc Brakes |
| Suspension | Adjustable Front Suspension (80mm travel) |
| Frame Material | Aluminum |
| Display | LCD Display |
| Control | Smart APP Control (Orbital Sports) |
| Max Weight Recommendation | 350 Pounds |
Figure 4: The 1200W peak motor provides strong power for various terrains.
Figure 5: The 26"x4.0" fat tires offer strong grip and anti-slip effect for diverse road conditions.
Figure 6: The high-density 48V/10AH removable battery ensures long travel range.
Figure 7: The all-aluminum frame with dual shock absorbers provides a smooth and comfortable ride.
Warranty and Support
The SISIGAD Electric Bike comes with a 0.5 Year Manufacturer Limited Warranty. For any issues during product use or installation, please contact the professional customer service team for assistance.
Contact Information: Please refer to your purchase documentation or the official SISIGAD website for the most current customer service contact details.
