1. Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your loosoo 160317 Single Cartridge Pool Filter Pump Assembly. Please read all instructions carefully before use and retain this manual for future reference.
The loosoo 160317 Single Cartridge Pool Filter Pump Assembly is designed to provide effective filtration for your pool or spa, ensuring clear and clean water. It is compatible with Pentair Clean & Clear CC150 systems and replaces EC-160317.
Image 1.1: The loosoo 160317 Single Cartridge Pool Filter Pump Assembly, a complete unit for pool and spa filtration.
2. Important Safety Information
WARNING: Failure to follow these instructions can result in serious injury or death.
- Always disconnect power to the pump before performing any service or maintenance.
- Ensure all plumbing connections are secure and leak-free before operating the filter.
- Do not operate the filter if any part is damaged or missing.
- This filter operates under high pressure. Failure to replace the locking ring if damaged or worn, or improper assembly, can result in the lid separating from the filter, causing severe injury or death.
- Keep children away from the filter area during operation and maintenance.
3. Product Overview
The loosoo 160317 Single Cartridge Pool Filter Pump Assembly features a robust design for efficient and reliable pool water filtration.
Key Components:
- High-Flow Manual Air Relief Valve: Located at the top, used to release trapped air.
- Pressure Gauge: Monitors internal filter pressure.
- Filter Lid: Top cover of the filter tank.
- Clamp Ring: Secures the filter lid to the tank body.
- Durable Filter Cartridges: The primary filtration media.
- Single-Piece Fiberglass-Reinforced Polypropylene Tank: Chemical-resistant and durable tank body.
- Inlet/Outlet Ports: 1.5-inch and 2-inch interfaces for plumbing connections.
- Drain and Washout: 1-inch drain for easy water removal.
Image 3.1: Internal structure diagram highlighting key components like the air relief valve, filter lid, clamp ring, cartridges, and tank body.
Image 3.2: Detailed views of the pressure gauge, clamp ring, and inlet/outlet connections.
4. Specifications
Below are the technical specifications for the loosoo 160317 Single Cartridge Pool Filter Pump Assembly:
| Feature | Specification |
|---|---|
| Model Number | 160317 |
| Compatibility | Pentair Clean & Clear CC150 (Replaces EC-160317) |
| Effective Filtration Area | 150 Square Feet |
| Flow Rate | 150 GPM (Gallons Per Minute) |
| Inlet/Outlet Interface | 1.5-inch and 2-inch |
| Drain Size | 1-inch |
| Material | Polypropylene, Polyvinyl Chloride |
| Item Weight | 34.2 pounds |
| Product Dimensions | 15.5"L x 15.5"W x 76"H |
Image 4.1: Visual representation of key product specifications.
5. Setup and Installation
Proper installation is crucial for the filter's performance and safety. If you are unsure about any steps, consult a qualified pool professional.
Installation Steps:
- Placement: Position the filter on a firm, level surface, ensuring adequate clearance for maintenance.
- Plumbing Connections: Connect the pool pump's discharge to the filter's inlet and the filtered water return line to the filter's outlet. Use appropriate fittings and sealants to prevent leaks. The filter supports both 1.5-inch and 2-inch pipe sizes.
- Install Pressure Gauge and Air Relief Valve: Securely thread the pressure gauge and the high-flow manual air relief valve into their designated ports on the filter lid.
- Cartridge Installation: Ensure the filter cartridge is properly seated inside the tank body.
- Secure Lid: Place the filter lid onto the tank body and secure it with the clamp ring. Ensure the clamp ring is properly engaged and tightened according to manufacturer specifications to prevent pressure leaks.
- Initial Fill: Before starting the pump, ensure the filter tank is filled with water.
Image 5.1: An example of a pool filter system setup, demonstrating the placement and plumbing connections.
Installation Video:
Video 5.1: An official video from LOOSOO AUTOPARTS demonstrating the installation and overview of the loosoo 160317 Single Cartridge Pool Filter Pump.
6. Operating Instructions
Once installed, follow these steps to operate your filter system:
- Prime the Pump: Ensure your pool pump is properly primed according to its manufacturer's instructions.
- Open Valves: Make sure all plumbing valves are open before the pump is turned on.
- Start Pump: Turn on the pool pump.
- Release Air: Open the high-flow manual air relief valve on top of the filter. The air relief valve should remain open until a steady stream of water flows out and all air is expelled from the filter tank. Close the air relief valve.
- Check Pressure: Note the initial clean operating pressure on the pressure gauge. This will be your baseline for determining when cleaning is needed.
7. Maintenance
Regular maintenance ensures optimal performance and longevity of your filter. Clean or replace cellular media as outlined below when the pressure gauge reading increases 10 PSI above the clean starting pressure.
Cellular Media Filter Maintenance Instructions:
- Stop pump and open air relief valve. Remove the drain plug.
- Remove locking ring and tank lid.
- Remove cellular media assembly by lifting handle on support tube.
- Remove cellular media from support tube and clean as necessary to remove debris.
- Clean and remove debris from inside the tank and from the O-ring and O-ring groove.
- Replace clean cellular media on support tube and install assembly into the filter body.
- Replace tank lid, making sure it is fully and firmly seated on tank body.
- Replace locking ring, turning it only until it hits the stops on the filter body.
- Be sure all plumbing valves are open before the pump is turned on.
- Open the air relief valve. Start the pump. The air relief valve should remain open until a steady stream of water flows and all air is expelled from the filter tank.
Winterization:
To winterize, drain the system by opening the air relief valve and removing the drain plug. Remove and clean the cellular media and store it in a dry place.
Image 7.1: A visual guide to the maintenance steps for the cellular media filter.
8. Troubleshooting
This section addresses common issues you might encounter with your pool filter assembly.
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Water Flow | Clogged filter cartridge, air in the system, pump issue. | Clean or replace cartridge. Bleed air from the system. Check pump for proper operation. |
| High Pressure Gauge Reading | Dirty filter cartridge. | Perform filter cartridge cleaning as per maintenance instructions. |
| Water Leaking from Filter | Loose clamp ring, damaged O-ring, cracked tank. | Ensure clamp ring is tightened correctly. Inspect and replace O-rings if damaged. Contact support if tank is cracked. |
| Cloudy Pool Water | Dirty filter, improper chemical balance, insufficient filtration time. | Clean filter cartridge. Test and adjust pool chemistry. Increase pump run time. |
9. Warranty and Support
loosoo is committed to providing quality products. We offer carefree replacement for our products. If you have any questions or require assistance with your loosoo 160317 Single Cartridge Pool Filter Pump Assembly, please do not hesitate to contact us. Our customer service team is eager to provide you with the best possible assistance.
For support, please refer to the contact information provided with your purchase or visit the official loosoo website.