Introduction
Thank you for choosing the VEVOR 50000 BTU Propane Patio Heater. This manual provides essential information for the safe assembly, operation, and maintenance of your new outdoor heating appliance. Please read all instructions carefully before use and retain this manual for future reference.
Safety Information
WARNING: For Outdoor Use Only. Do not operate this heater indoors or in enclosed spaces.
- Always operate the heater on a firm, level surface.
- Maintain adequate clearance from combustible materials (e.g., walls, ceilings, fabrics).
- Ensure proper ventilation during operation.
- Keep children and pets away from the heater.
- Do not move the heater while it is in operation or still hot.
- Equipped with a tilt auto-shutoff sensor for enhanced safety. If the heater tilts beyond 45 degrees, it will automatically shut off.
- Always turn off the gas supply at the propane tank when the heater is not in use.
- Never store a propane cylinder indoors or in an enclosed area.
Parts List
Before assembly, ensure all parts are present and undamaged. Refer to the diagram below for identification.
Figure 1: Exploded view of VEVOR Patio Heater components, including Aluminum Cover, Burner Head, Upper Main Support Bar, Lower Main Support Bar, Pail, Legs, Chassis, and Wheel Assembly.
- Aluminum Cover (1x)
- Burner Head (1x)
- Upper Main Support Bar (1x)
- Lower Main Support Bar (1x)
- Pail (1x)
- Legs (3x)
- Chassis (1x)
- Wheel Assembly (1x)
Setup and Assembly
Follow these steps for quick and easy assembly. It is recommended to have two people for certain steps.
Figure 2: Visual guide for the 4-step quick installation process.
- Step 1: Assemble the Base - Attach the wheels and support bar to the chassis.
- Step 2: Reinforce with Screws - Securely fasten the legs and support bars with the provided screws.
- Step 3: Assemble the Box Cover and Combustion Heater - Install the pail and the burner head assembly.
- Step 4: Finally Assemble the Reflector - Attach the aluminum cover (reflector) to the top of the burner head.
Ensure all protective films, especially blue ones, are removed from reflective surfaces before operation to prevent burning and damage.
Operating Instructions
Your VEVOR Patio Heater features a convenient one-touch ignition system and adjustable heat control.
Figure 3: Detailed steps for one-touch ignition.
- Connect Propane Tank: Ensure the propane tank is securely connected and the tank valve is open.
- Step 1: Press and Rotate Knob: Press and rotate the control knob to the 'HI' position. Hold for 3 seconds.
- Step 2: Press Igniter Button: Simultaneously press the igniter button until the flame lights. Continue holding the control knob for 10 seconds after ignition to ensure the thermocouple is heated.
- Adjust Heat: Once lit, release the control knob. You can then adjust the heat output from 'LO' to 'HI' by rotating the knob.
To turn off the heater, rotate the control knob to the 'OFF' position and close the valve on the propane tank.
Maintenance
Regular maintenance ensures optimal performance and longevity of your patio heater.
- Cleaning: Clean the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Burner Maintenance: Periodically inspect the burner and flame tube for any obstructions or damage. Ensure the burner ports are clear.
- Gas Line Inspection: Regularly check the gas hose and connections for leaks or signs of wear. Perform a leak test with soapy water if any issues are suspected.
- Storage: When not in use for extended periods, disconnect the propane tank and store the heater in a dry, protected area. Consider using a weather-resistant cover.
Troubleshooting
If your heater is not operating correctly, consult the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater will not light | No gas supply / Low gas pressure | Check propane tank level and ensure valve is fully open. |
| Pilot light will not stay lit | Thermocouple dirty or faulty | Clean or replace thermocouple. Ensure control knob is held long enough after ignition. |
| Low heat output | Low gas pressure / Partially blocked burner | Check propane tank level. Inspect and clean burner ports. |
| Heater shuts off unexpectedly | Tip-over switch activated / Low oxygen sensor activated | Ensure heater is on a stable surface. Check for adequate ventilation. |
Specifications
- Brand: VEVOR
- Model Number: STD (PRO)
- Heat Output: 50000 British Thermal Units
- Heating Coverage: Up to 18 feet diameter
- Fuel Type: Propane
- Ignition Method: Piezo Ignition
- Material: Iron, Stainless Steel, Aluminum Cap
- Color: Silver
- Item Dimensions (D x W x H): 32.01"D x 32.01"W x 87.4"H
- Item Weight: 32.2 Pounds
- Special Features: Adjustable Height, Weatherproof, Wheels, Tilt Auto-Shutoff Sensor
Warranty and Support
For warranty information or technical support, please refer to the documentation included with your purchase or visit the official VEVOR website. Keep your purchase receipt as proof of purchase.
