Pellethead 841-0970 Wireless Remote Control Thermostat User Manual

1. Introduction

This manual provides instructions for the installation, operation, and maintenance of your Pellethead 841-0970 Wireless Remote Control Thermostat. This device is designed to provide wireless thermostat and timer control for compatible gas stoves and fireplaces. It serves as a direct wired replacement for HHT P/N SMART-STAT-HHT, SMART-STAT-IV, and 841-0970, and is an ideal replacement for Heatilator, Heat N Glo, Majestic, and Quadra-Fire Gas Stove and Fireplace Models.

Key Features:

• Wireless thermostat and timer control functionality.
• 5-button interface for intuitive control: MODE, SET, TIMER, UP, DOWN.
• Clear LCD screen displaying 24-hour clock, room temperature (°F or °C), and a flame icon to indicate appliance operation.
• Timer settable in fifteen-minute increments, up to 9 hours.
• 110V plug-in receiver with 18-inch wires.
• Receiver can learn up to two additional Skytech remotes.

2. Safety Information

Please read and understand all instructions before installing or operating this product. Failure to follow these instructions may result in property damage, personal injury, or death. Always consult a qualified technician for installation if you are unsure about any steps.

• Ensure the fireplace or stove is turned off and cooled before beginning installation.
• Do not expose the remote control or receiver to water or excessive humidity.
• Keep batteries out of reach of children.
• Replace batteries with the correct type and ensure proper polarity.

3. Package Contents

Verify that all items are present in the package:

• Wireless Remote Control
• Receiver Unit
• Wiring Harness (18-inch wires)
• Instruction Manual (this document)
• Batteries (typically AAA for remote, not explicitly stated but implied by image)

Image 1: Components of the Pellethead 841-0970 Wireless Remote Control Thermostat. Shown are the remote control, the receiver unit, connecting wires with terminals, and two AAA batteries.

4. Setup and Installation

Installation involves connecting the receiver to your fireplace or stove's control system. It is recommended to have this installed by a qualified technician if you are not familiar with electrical wiring.

1. Power Off: Ensure the power to your fireplace or stove is completely turned off at the circuit breaker before beginning installation.
2. Receiver Placement: Position the receiver unit in a location where it is protected from heat and moisture, but still within range of the remote control. The receiver is a 110V plug-in design.
3. Wiring Connection: Connect the 18-inch wires from the receiver to the appropriate terminals on your fireplace or stove's control board. Refer to your appliance's manual for specific wiring diagrams. This unit is a direct wired replacement for specific HHT models.
4. Power On: Once wiring is complete and secure, restore power to the fireplace or stove.
5. Battery Installation (Remote): Open the battery compartment on the back of the remote control and insert the batteries, observing correct polarity.
6. Pairing (Learning Function): The receiver has a "learn" function. Follow the instructions provided with the receiver to pair it with the remote control. This typically involves pressing a "learn" button on the receiver and then a button on the remote. The receiver can learn up to two additional Skytech remotes.

5. Operating Instructions

The remote control features a 5-button interface and an LCD screen for easy operation.

Remote Control Buttons:

• MODE: Cycles through operating modes (e.g., ON, THERMO, OFF).
• SET: Used to confirm settings or enter programming mode.
• TIMER: Activates and adjusts the timer function.
• UP (▲): Increases values (temperature, time).
• DOWN (▼): Decreases values (temperature, time).

LCD Display:

• 24-hour clock: Displays current time.
• Room Temperature: Shows the current ambient temperature in °F or °C.
• Flame Icon: Indicates when the connected appliance is actively operating.

Basic Operation:

1. Turning On/Off: Use the MODE button to switch the appliance ON or OFF.
2. Setting Temperature: In THERMO mode, use the UP/DOWN buttons to set your desired temperature. The system will automatically adjust the appliance to maintain this temperature.
3. Using the Timer: Press the TIMER button, then use UP/DOWN to set the desired operating duration in 15-minute increments, up to 9 hours. Press SET to confirm.
4. Setting Clock: Refer to the detailed instructions in the remote's specific manual for setting the 24-hour clock.

6. Maintenance

• Cleaning: Wipe the remote and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
• Battery Replacement: Replace batteries in the remote control annually or when the low battery indicator appears on the LCD screen. Use only the specified battery type.
• Receiver Check: Periodically check the receiver's wiring connections to ensure they are secure.

7. Troubleshooting

If you experience issues with your wireless remote control thermostat, refer to the following common solutions:

• No Response from Appliance:
  • Check remote control batteries and replace if necessary.
  • Ensure the receiver is properly plugged into a 110V outlet and has power.
  • Verify the wiring connections between the receiver and the appliance are secure.
  • Re-pair the remote control with the receiver using the "learn" function.
  • Ensure the remote is within range of the receiver.
• Incorrect Temperature Reading:
  • Ensure the remote control is not placed near a heat source or in direct sunlight.
  • Verify the temperature unit (°F or °C) is set correctly.
• Timer Not Functioning:
  • Ensure the timer is properly set and confirmed with the SET button.
  • Check if the appliance is in a mode that supports timer operation.

For persistent issues, contact Pellethead customer support.

8. Specifications

9. Compatibility

The Pellethead 841-0970 Wireless Remote Control Thermostat is compatible with a wide range of gas stove and fireplace models, including but not limited to:

Direct Replacement For:

• HHT: P/N SMART-STAT-HHT, SMART-STAT-IV, 841-0970
• Skytech's SMART STAT IV (ideal replacement)

Compatible Brands and Models:

This unit is compatible with many models from the following brands. Please verify your specific model number against the list below or consult your appliance's manual for remote control compatibility.

• Quadra-Fire Gas Models: Castile Gas, Colbay & Colbay Insert, Garnet, Hudson Bay & Hudson Bay Insert, QFP30 (Remington), QV-PIER, QV-ST, QV32, QV36, QVI-25FB, QVI-30FB, QVI-35FB, QVI25, QVI30, QVI35, Sapphire, Topaz.
• Quadra-Fire Pellet Models: 1200 & 1200i Insert, Castile & Castile Insert, Mt Vernon OE, Outfitter I & Outfitter II, Santa Fe & Santa Fe Insert, Trekker & Trekker Insert.
• Majestic Models: JASPER30IN, MERC32IL, MERC32IN, MERC32VL, MERC32VN, OXDV30-IPI.
• Heat-N-Glo Models: 4000INC & 4000INS, 6000TRXI & 6000TRXI-IPI, AT-Grand, Gem-36 & Gem-42, Grand-XT, Mission Bay, Paloma-Mod, Supreme-XT, and numerous other models listed in the product description (too extensive to list all here, refer to product listing for full list).
• Heatilator Pellet Models: CAB50, PS35 & PS50.
• Heatilator Gas Models: ADVR3428, ADVR3428I, ADVR3428IL, AZTEC & AZTECLP, GDST3831I, MDV3732, MDV3732-B, MDV3732-C, NDV4842IL-B, NDV4842I-B, NDV4236IL-B, NDV4236I-B, NDV3933IL-B, NDV3933I-B, NDV3630IL-B, NDV3630I-B, NBV4842I-B, NBV4236I-B, and numerous other models listed in the product description (too extensive to list all here, refer to product listing for full list).

10. Warranty and Support

For warranty information or technical support regarding your Pellethead 841-0970 Wireless Remote Control Thermostat, please contact Pellethead customer service. Refer to the product packaging or the Pellethead website for current contact details.

Manufacturer: Pellethead

Date First Available: September 24, 2024